A circuit has a 15022 resistor in series with a 10mH inductor. The voltage input is...
Consider a series RLC circuit where the output voltage y(t) is taken across the resistor and the input is the voltage x(t). (a) Find the transfer function of this filter. (b) What is the type of this filter?
A circuit has an ac voltage source and a resistor and capacitor connected in series. There is no inductor. The ac voltage source has voltage amplitude 0.900 kV and angular frequency w = 20.0 rad/s. The voltage amplitude across the capacitor is 0.500 kV. The resistor has resistance R= 0.300 kΩ. Part A What is the voltage amplitude across the resistor? Part B What is the capacitance C of the capacitor? Part C Does the source voltage lag or lead the current? Part D What is the average...
4. An electrical filter circuit is built with a series resistor (R), inductor (L) and capacitor (C). The ratio of resistor voltage (output) to source voltage (input) is given by H is the magnitude of a complex number, where ZL=JwL ZC = 1 / (j w C) andjsVT (same as 1) w frequency (radians/sec) 2 f,where f is frequency in Hz. For each exercise, assign the values of R, L and C and set the recommended frequency range. Then have...
A generator is connected to a resistor and a 0.028-H inductor in series. The rms voltage across the generator is 9.5 V. When the generator frequency is set to 110 Hz, the rms voltage across the inductor is 3.5 V. Determine the resistance of the resistor in this circuit.
Input voltage is applied to a circuit consisting of a series connection of capacitor C=10 uF ("u"="micro") and resistor R=60 Ohm. The output voltage is the voltage across resistor R. Find the corner frequency omc of the circuit in rad/s (do not enter the units). Submit Answer Tries 0/3 Using the graph windows below, generate Bode plots for the magnitude and phase of the transfer function H in the com/omc) range from 0.01 to 100- The horizontal axis (omega-axis) has...
A generator is connected to a resistor and a 0.029-H inductor in series. The rms voltage across the generator is 7.6 V. When the generator frequency is set to 134 Hz, the rms voltage across the inductor is 2.7 V. Determine the resistance of the resistor in this circuit. Ω
You have a 170-Ω resistor and a 0.430-H inductor. Suppose you take the resistor and inductor and make a series circuit with a voltage source that has a voltage amplitude of 25.0 V and an angular frequency of 210 rad/s . a.)What is the impedance of the circuit? b.)What is the current amplitude? c.)What is the voltage amplitude across the resistor? d.)What is the voltage amplitudes across the inductor? e.)What is the phase angle ϕ of the source voltage with...
You have a 190-Ω resistor and a 0.420-H inductor. Suppose you take the resistor and inductor and make a series circuit with a voltage source that has a voltage amplitude of 31.0 V and an angular frequency of 210 rad/s . 1) What is the impedance of the circuit in ohms? 2) What is the current amplitude? 3) What is the voltage amplitude across the resistor? 4) What is the voltage amplitudes across the inductor?
Find the transfer function H(jω) for the circuit above as a function of jω. (Leave R and L as variables). Assume V R to be the output and V S to be the input. С L RVR(t) vs (t) A. Find the transfer function H(jo) for the circuit above as a function of jaw. (Leave R and L as variables). Assume V to be the output and V to be the input. S R B. Find the Magnitude and Phase...
5) Consider the following second-order bandpass filter. As input voltage, apply V(t) 100Ω, C-4.7 μF. and L-10mH. sin(wt).R in Vout Fig 9: Second-order band-pass filter a) Determine the frequency response function H(ju) Ve-ju) / Vm(ju) and sketch the magnitude and phase characteristics versus w by calaulation. Calculate the theoretical cutoff frequency of the filter Using PSpice AC analysis, plot magnitude lHju)l and phase ф characteristics of the filter, between 1 Hz-100 KHz b) c) 5) Consider the following second-order bandpass...