Knowing that each pin has a 3/8-in diameter, determine the average Link BD consists of a...

Question

Question

Answer 1

Answer #1

Given hat Take momentum attut ar diagtam 18 x BD Lcoso tano Sino coss-section area obBp FBD BD 3.46y 2 5]16)

Answer 2

Similar Homework Help Questions

! Required information Part 1 of 2 Link BD consists of a single bar 1 in....

! Required information Part 1 of 2 Link BD consists of a single bar 1 in. wide and in. thick. Each pin has a 3 -in. diameter and P 5 kips. P 10 points 6 in B еВook 12 in Hint Print 30 References Determine the maximum value of the average normal stress in link BD if e 0 The maximum magnitude of the average normal stress is ksi. This stress is in (Click to select)
Link BD consists of single bar 1 in. wide and t in. tick Each pin has...

Link BD consists of single bar 1 in. wide and t in. tick Each pin has a t-in. diameter and P-4 kips. 30° References Section Break Difficulty. Easy value: 0.93 points You did not receli Determine the maximum value of the average normal stress in link BD if e-90. (Round the final answer to two decimal places.) The maximum magnitude of the average normal stress is 11.085 ksi. This stress is in compression
In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are...

In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B and D. The ultimate shearing stress is 159 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. (Round the final answer to three...

Problem 7 In the hanger shown, the upper portion of link ABC is 3/8 in. thick...

Problem 7 In the hanger shown, the upper portion of link ABC is 3/8 in. thick and the lower portions are each 1/4 in. thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A has a 3/8 in. diameter, while a 1/4 in. diameter pin is used at C. Determine (a) the shearing stress in pin A, (b) the shearing stress in pin C, (c) the largest normal stress in link ABC,...
1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins...

1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that ink BD is not reinforced around the pin holes Front view 18 mm Side...
Question 2 beam is supported by a pin at A and a short link BC. If P= 15 kN, determine the average shear stres...

Question 2The beam is supported by a pin at A and a short link BC. If P= 15 kN, determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as shown, and each has a diameter of 18 mm.

(10 points) Link AD is connected to link BCD at D by a pin. The pin...

(10 points) Link AD is connected to link BCD at D by a pin. The pin is made of steel with 600 MPa ultimate shearing stress and is in single shear. Knowing the factor of safety of 3 is desired for the pin at D, determine the diameter of the pin at D when the loading at C is 6000 N iom 6000N Figure 1: Two links
1.52 Solve Prob. 1.51, assuming that the structure has been redesigned to use 16-in.-diameter pins at...

1.52 Solve Prob. 1.51, assuming that the structure has been redesigned to use 16-in.-diameter pins at A and C as well as at B and that no other changes have been made. A in. 8 in. B C 4 in. 6 in. Fig.P1.51 1.51 Link AC is made of a steel with a 65-ksi ultimate normal stress and has a 2-in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter...
Link AB, of width b = 2 in and thickness t = 1/4 in . is...

Link AB, of width b = 2 in and thickness t = 1/4 in . is used to support the end of a horizontal beam Knowing that the average normal stress in the link is - 20 ksi and that the average shearing stress in each of the two pins is 12 ksi. determine the diameter d of the pins. the average bearing stress in the link

Draw FBDs as required Clearly state all assumptions made towards solving the problem 1) In the...

Draw FBDs as required Clearly state all assumptions made towards solving the problem 1) In the structure shown, 큭in dia. pin is used at A and jin dia, pins are used at B and D If the thickness of member BD is ^in, the ultimate shearing stress for the pins at A, B&D are 5ksi and the ultimate normal stress for the link BD is 8ksi and the overall factor of safety of 3 is desired. Determine the allowable horizontal...