Just wanna check if this is right? s. (20 pts) Use Wye . Delta transfornations to...

Question

Question

Just wanna check if this is right?

s. (20 pts) Use Wye . Delta transfornations to deternmine v and v in the circuit below 2 92 2 02 12v 넥2 62-1) (2.24)帆(42s):

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

Just wanna check if its right? Shin 3 2 (20 pts) Use nodal analysis to find...

Just wanna check if its right? Shin 3 2 (20 pts) Use nodal analysis to find V, in the circuit belotw 40 V ( 20Ω 16 2 ao 0 10 10 10 60v A- n a-40 v 醫. : 60
Problem 2:Three phase droult (42 pts) A three-phase wye connected generator ﹃plies two paral el loads...

Problem 2:Three phase droult (42 pts) A three-phase wye connected generator ﹃plies two paral el loads through a feeder. tad is matalaeeday connected load and load 2 is a balanced delta connected loed. System data: Generator: Rating S-5oo MVA; Line Voltage: Veu-25KV; Feeder impedance: 7-(0.08 jo 62) O/mile, length-8 miles Generator reactance Xe- 1108: P.-75MW pf c-o.78 (all the power factors are lagging) (a) Draw the one-line diagram and a three-phase equivalent circuit (8pts) (b) Calculate the generator and feeder...
The three figures below show a balanced three phase Delta, its Wye equivalent and the single...

The three figures below show a balanced three phase Delta, its Wye equivalent and the single phase equivalent of the three phase Wye. All three representations have a complex load ZALD or ZYLD and a complex line impedance ZLINE Refer to these diagrams when answering questions 1-4. ZLINE Vab= 679 L 30° ZLINE ZALD ZLINE = 2+1 DELTA ZALD= 18+24j2 LINE ZLINE ZLINE ZYLD 7yun WYE WYE ZYLD ZLINE ZLINE Van Complex Load ZYLD Single Line WYE 1) In the...

5000 10.2 S pts) The Zener diode in the circuit on the right voltage V 20...

5000 10.2 S pts) The Zener diode in the circuit on the right voltage V 20 = 8.5V., and Zener resistancerz the circuit on the right has a Zener d) Find the Thevenin equivalent circuit as seen by lo b) Find the output voltage if a loa Find the output voltage if a load R, is connected and it draws a 1.5 mA current. Determine the value of RL c) How small can the load R, be, while ensuring that...
Question 2: (20 pts.) In the circuit below E =12V, R1 = R2 = 10 ohm,...

Question 2: (20 pts.) In the circuit below E =12V, R1 = R2 = 10 ohm, and C = 4 uF. Initially the switch Sis open. At t=0 the switch S is closed. (a) What is the current i, through R, at t= 0 and t = 00 ? (b) Draw a qualitative graph of the potential drop V, through R. from t=0 to t=00. (c) When C is fully charged, switch S is opened. What is the current iz...
Problem 2 (20 pts): Mohr's Circle Use the Mohr circle shown on the right to answer...

Problem 2 (20 pts): Mohr's Circle Use the Mohr circle shown on the right to answer the questions below. 20 B (a) Determine the state of stress (Ox, Oy, Txy) [ksi] depicted in the drawing of Mohr's circle. (b) Find the principle stresses (01, 02) [ksi] and the respective angles of principle stress (Opl, Op2). (c) Calculate the maximum shear stress (Tmax) [ksi] and the angles of maximum shear stress (Os1, 0:2). -20 20 40 60 02 0 01 [ksi]...

just multisim 2. (20 pts) Use Nodal Analysis to determine Node Voltages Vi and V2 12...

just multisim 2. (20 pts) Use Nodal Analysis to determine Node Voltages Vi and V2 12 ЗА V. R3 40 R1 R4 80 R5 20 6 A 20
i just wanna double check whether i answered correct or not please. Why do we measure...

i just wanna double check whether i answered correct or not please. Why do we measure the volume of the flask in this experiment with water rather than using the volume listed on the side? Select all correct answers that apply. Must include all correct answers for full credit. The volume is not accurate on a flask to the number of significant figures required for this experiment The volumetric markings on the flask do not extend to it's full height...
ANSWER ALL PLEASE Question 20 2 pts In the Figure below, V1 = 14 V, V2...

ANSWER ALL PLEASE Question 20 2 pts In the Figure below, V1 = 14 V, V2 = 8 V, V3 = 10 V, R1 = 2.00, R2 = 4.0, and R3 = 2.00 Find the electric currents is, iz, and is. (Hint: use the junction a and the two loops). RI R 14 M4 Equations: Kirchoff's Junction (node) rule: 11 = 12 + iz Kirchoff's Loop rule (left loop): V1 - iRi - iz R2 + V2 = 0 Kirchoffs...

s Question: 2 pts 13 of 20 (20 complete) This Test: 48 pts possible -re the...

s Question: 2 pts 13 of 20 (20 complete) This Test: 48 pts possible -re the given quadrilaterals similar? Tell why or why not. 12 4. 12 5 15 Choose the correct answer below. O A. No, because not all the lengths of the corresponding sides are proportional and/or not all the corresponding angles are congruent. OB. Yes, the quadrilaterals are similar because all corresponding angles are congruent and all corresponding sides are proportional OC. Yes, the quadrilaterals are similar...