Homework Answers
Add Answer to:
The strain in the x direction at point A on the A-36 structural-steel beam is measured...
1) (50 pts) On a structural steel I profile beam a distributed load and M moment...
1) (50 pts) On a structural steel I profile beam a distributed load and M moment is applied as shown in the figure. According to given parameters below, please solve the problem with finite element method (ANSYS Student-Structural Module) to determine; a) the maximum bending in mm, b) the average shear stress, c) distributed load plot (F- x plot), d) equivalent stress contour plot, e) total deformation contour plot. (Ebeam=200 GPa, Wo=10 N/m, L=1 m., M=254 N.m, h=154 mm., b=77...
Asap 1. The bracket is made of steel (Young's modulus 200 GPa; Poisson's ratio 0.3). When the force P is applied to the bracket, the gages in the strain rosette at point A have the followi...
Asap
1. The bracket is made of steel (Young's modulus 200 GPa; Poisson's ratio 0.3). When the force P is applied to the bracket, the gages in the strain rosette at point A have the following readings: E.-60 μ . Ep 135 μ l, and E.-264 μ (a) Determine the shear strain at point A. (b) Determine the orientation of the principal plane, the in-plane principal strains, the maximum in-plane shear strain, and the average in-plane normal strain. Determine the...
Question 3 For the simply supported steel beam with cross section and loading shown (see Figure...
Question 3 For the simply supported steel beam with cross section and loading shown (see Figure 3a), knowing that uniformly distributed load w=60 kN/m, Young modulus E = 200 GPa, and yield stress Cyield=200 MPa (in both tension and compression). ул 15 mm w=60 kN/m ... 1 B A 15 mm + 300 mm IC - i 2.5m 1 1 15 mm 7.5m 1 150 mm Figure 3a (a) Check if: the beam is safe with respect to yielding (using...
A rigid beam AB is supported by a hinge at A and by a steel wire...
A rigid beam AB is supported by a hinge at A and by a steel wire CD, 2.50mm in diameter and 300mm long, as shown. With no load applied on the beam, the end B is 2mm above the contact point E. Determine the elongation of CD just to touch point E. For the steel wire, E=200GPa. Express your answer in mm and use two decimal places. D W = 40 kg 44 Steel wire 2.5 mm E=200 GPa 300...
The simply supported beam consists of a w530 x 66 structural steel wide-flange shape [E-200 GPa; I -351 x 106 mm]. Determine (a) the beam deflection at point C. (b) the beam deflection at point E. As...
The simply supported beam consists of a w530 x 66 structural steel wide-flange shape [E-200 GPa; I -351 x 106 mm]. Determine (a) the beam deflection at point C. (b) the beam deflection at point E. Assume P = 35 kN, w = 80 kN/m, LAB = LBC = LCD = 4 m, LDE = 2 m LAB BC Answers: (a) vc=T-190.693 (b) VE178.156
The simply supported beam consists of a w530 x 66 structural steel wide-flange shape [E-200 GPa;...
An existing steel beam is in use in a building.
An existing steel beam is in use in a building. Using a rectangular strain gauge rosette, the actual strains at point A have been recorded while being subjected to test loads which simulate crowd loading. It is necessary to calculate the principal stresses to check whether the beam is safe for its current purpose (ie: assess whether the stresses determined are less than the maximum permissible stresses) Figure 4: Strain gauge rosette location and recorded strains In this case it is reasonable...
The simply supported beam consists of a W410 × 60 structural steel wide-flange shape [E =...
The simply supported beam consists of a W410 × 60 structural
steel wide-flange shape [E = 200 GPa; I = 216 ×
106 mm4]. For the loading shown, determine
the beam deflection at point C.
Assume P = 53 kN, w = 91 kN/m,
LAB = LBC = 1.7 m,
LDE = LCD=1.8 m,
MA = 197 kN-m.
200 GPa; I 216 x 100 mm ]. For the loading shown, determine the beam The simply supported beam consists of a...
The measured strain values at point Q are as follows: Ea = 40(10), Eb = 980(10),...
The measured strain values at point Q are as follows: Ea = 40(10), Eb = 980(10), &c = 330(10) 1) Calculate the strain components Ex, Ey and Yxy at point Q. 2) Calculate the stress components Ox, Oy and Txy at point Q. 3) Determine the principal stresses at point Q, using Mohr's circle. The Young's modulus E = 200 GPa, shear modulus G = 76.9 GPa, Poisson's ratio v= 0.29. 《 s,
X Not Correct The cantilever beam consists of a rectangular structural steel tube shape [E =...
X Not Correct The cantilever beam consists of a rectangular structural steel tube shape [E = 180 GPa; I = 151 x 106 mm4]. For the loading shown, determine: (a) the beam deflection VA at point A. (b) the beam deflection VB at point B. Assume P = 88 kN, Q = 29 kN, MB = 217 kN-m, w = 60 kN/m, LAB = 1.8 m, LBC = 2.6 m. P w с MB B LAB LBC Answers: X (a)...
The composite beam is constructed from wood and reinforced with a steel strap 10 mm 300...
The composite beam is constructed from wood and reinforced with a steel strap 10 mm 300 mm 10 mm 175 mm 52 kN. Take E 200 GPa E= 15 GPa. It is subjected to a shear of V TUDICll.23 Part A Use the method of composite beams and calculate the maximum shear stress in the beam Express your answer to three significant figures and include appropriate units ? Value Units Tmax= Submit Request Answer Provide Feedback
The composite beam is...
1) (50 pts) On a structural steel I profile beam a distributed load and M moment is applied as shown in the figure. According to given parameters below, please solve the problem with finite element method (ANSYS Student-Structural Module) to determine; a) the maximum bending in mm, b) the average shear stress, c) distributed load plot (F- x plot), d) equivalent stress contour plot, e) total deformation contour plot. (Ebeam=200 GPa, Wo=10 N/m, L=1 m., M=254 N.m, h=154 mm., b=77...
Asap
1. The bracket is made of steel (Young's modulus 200 GPa; Poisson's ratio 0.3). When the force P is applied to the bracket, the gages in the strain rosette at point A have the following readings: E.-60 μ . Ep 135 μ l, and E.-264 μ (a) Determine the shear strain at point A. (b) Determine the orientation of the principal plane, the in-plane principal strains, the maximum in-plane shear strain, and the average in-plane normal strain. Determine the...
Question 3 For the simply supported steel beam with cross section and loading shown (see Figure 3a), knowing that uniformly distributed load w=60 kN/m, Young modulus E = 200 GPa, and yield stress Cyield=200 MPa (in both tension and compression). ул 15 mm w=60 kN/m ... 1 B A 15 mm + 300 mm IC - i 2.5m 1 1 15 mm 7.5m 1 150 mm Figure 3a (a) Check if: the beam is safe with respect to yielding (using...
A rigid beam AB is supported by a hinge at A and by a steel wire CD, 2.50mm in diameter and 300mm long, as shown. With no load applied on the beam, the end B is 2mm above the contact point E. Determine the elongation of CD just to touch point E. For the steel wire, E=200GPa. Express your answer in mm and use two decimal places. D W = 40 kg 44 Steel wire 2.5 mm E=200 GPa 300...
The simply supported beam consists of a w530 x 66 structural steel wide-flange shape [E-200 GPa; I -351 x 106 mm]. Determine (a) the beam deflection at point C. (b) the beam deflection at point E. Assume P = 35 kN, w = 80 kN/m, LAB = LBC = LCD = 4 m, LDE = 2 m LAB BC Answers: (a) vc=T-190.693 (b) VE178.156
The simply supported beam consists of a w530 x 66 structural steel wide-flange shape [E-200 GPa;...
The simply supported beam consists of a W410 × 60 structural
steel wide-flange shape [E = 200 GPa; I = 216 ×
106 mm4]. For the loading shown, determine
the beam deflection at point C.
Assume P = 53 kN, w = 91 kN/m,
LAB = LBC = 1.7 m,
LDE = LCD=1.8 m,
MA = 197 kN-m.
200 GPa; I 216 x 100 mm ]. For the loading shown, determine the beam The simply supported beam consists of a...
The measured strain values at point Q are as follows: Ea = 40(10), Eb = 980(10), &c = 330(10) 1) Calculate the strain components Ex, Ey and Yxy at point Q. 2) Calculate the stress components Ox, Oy and Txy at point Q. 3) Determine the principal stresses at point Q, using Mohr's circle. The Young's modulus E = 200 GPa, shear modulus G = 76.9 GPa, Poisson's ratio v= 0.29. 《 s,
X Not Correct The cantilever beam consists of a rectangular structural steel tube shape [E = 180 GPa; I = 151 x 106 mm4]. For the loading shown, determine: (a) the beam deflection VA at point A. (b) the beam deflection VB at point B. Assume P = 88 kN, Q = 29 kN, MB = 217 kN-m, w = 60 kN/m, LAB = 1.8 m, LBC = 2.6 m. P w с MB B LAB LBC Answers: X (a)...
The composite beam is constructed from wood and reinforced with a steel strap 10 mm 300 mm 10 mm 175 mm 52 kN. Take E 200 GPa E= 15 GPa. It is subjected to a shear of V TUDICll.23 Part A Use the method of composite beams and calculate the maximum shear stress in the beam Express your answer to three significant figures and include appropriate units ? Value Units Tmax= Submit Request Answer Provide Feedback
The composite beam is...
Most questions answered within 3 hours.
-
How many ways can 2 people be chosen and arranged in a straight
line if there...
asked 42 minutes ago -
(Problem 1d). Leandro has 16 hours per day that he can allocate
to work or leisure....
asked 1 hour ago -
Morganton Company
makes one product and it provided the following information to help
prepare the master...
asked 1 hour ago -
2Al + 3Cl2 --> 2AlCl3
If one mole Al is reacted w two moles Cl2, how...
asked 2 hours ago -
1. You will see some trends in the movement of each currency vs.
the US Dollar....
asked 2 hours ago -
9. (9 pts) An investor with a stock portfolio worth several
hundred thousand dollars sued his...
asked 3 hours ago -
Which statement is true?
a. Unless directed otherwise, the computer automatically
executes C. statements one before...
asked 3 hours ago -
When a new company is considering Speed to Market for a product
launch, which would provide...
asked 4 hours ago -
bacteria and their metabolites could either promote or protect from
cancer. Explain one of these cases...
asked 4 hours ago -
Use the sample data and confidence level given below to complete
parts (a) through (d).
A...
asked 4 hours ago -
During laser vision correction, a brief burst of 193 nm
ultraviolet light is projected onto the...
asked 4 hours ago -
1 ) How well does the initial speed, v0,calculated from Equation
4 agree with the value...
asked 4 hours ago