Given the specification of the motors!
1) what power,current, and voltage should I supply to get the full torque?
2) If I am delivering only 6V and 220mA, what will be the speed and torque ?
3)If I have load of 2lb, what will be the speed and torque assuming that the voltage is 9V and 300mA?
1.Rated voltage: DC12V; No-load speed: 250RPM; Rated torque: 5kg.cm; Rated Current: 870mA. Given the specification of...
A 12-pole, brushless, DC motor has a no-load speed of 5000rpm and a stall torque of 50 in-oz when operating at rated voltage of 60V. Testing shows that no-load speed and stall torque vary linearly with applied voltage. Also, with a constant applied voltage the speed decreases linearly as delivered torque increases. Calculate the following: Torque that the motor delivers at 2000 rpm when operated at rated voltage. T a) b) Fundamental frequency of the applied voltage waveform at this...
Q5.8:The specifications of machine 5.8. For the machine in the previous question, calculate (a) its no-load speed (b)its rated efficiency-olcoxL-n/nN (c) the following when the speed is zero (stall condition) (i)induced voltage (ii) nput current (ii) output torque (iv) ut power (v)output power (vi) efficiency (d) he speed (in rpm) when the torque is 0.2 Nm 5 A DC machine has a no-load speed of 10,000 rpm and a rated speed of 8,000 rpm when operating with its rated supply...
A separated excited dc machine is delivering 50% rated torque at 20% rated speed. Find the efficiency of the motor at this operating point. The details of the machine are as follows: 1500 kW(rated output power), 600V(rated voltage), 2650A (rated current) 600rpm (rated speed), brush voltage drop = 2V, Filed power input = 50 kW, Ra=3.645 mOhm, La=0.1 mH, Machine frictional torque coefficient = 15 Nm/rad/s. Field current is constant and armature voltage is variable.
A separately excited DC motor has the following data P=32kW (rated power); Va=220V (rated voltage); Ia=171A (rated curent); n=1000 rpm (rated speed); Ra = 0.096 ohm a.Calculate the armature voltage to reduce the speed to 900 rpm, assuming the load torque is kept constant? b.Calculate the resistance should be added to armature circuit to reduce the speed to 800 rpm, assuming the load torque is kept constant? c.Calculate the reduction of magnetic flux to reach the speed of 1100 rpm,...
please answer 13.16 at rated load of unity power factor and rated terminal voltage, determine efficienc including field rheostat loss. Ans. 93.139 13.11 A generator under test is rated at 100 KVA, 3-phase, 60-Hz; 2,400 volts. (a) If driven b a de motor unexcited, the motor output is 1.26 KW. (b) If driven by a de motor, generato on open circuit and excited to generate rated potential, the motor output is 2.5 KW. ( Ifdriven by a de motor, generator...
QUESTIONS Question-3: Draw "speed vs. torque" curve using data in Table-1. The completed graph represents the speed vs. torque characteristics of a typical DC shunt-wound motor. Terax Question-4: Calculate the speed regulation (full load - 12 lbf.in) using the equation: 2-143) 143 (no load Regulation (full load speed) Speed regulation- % Part-II - Motor Efficiency Calculation: Set the dynamometer control knob at its full CW position (to provide the maximum starting load for the shunt-wound motor). Turn on the power...
An engine with linear torque-(speed) characteristic and rated data 12 hp, 1800 rpm, serves two load types with characteristic torque a) and b) and a transmission gearbox c) as shown below in the photo: Assuming that for a rated voltage operation the starting torque is Ts=80 Nm. 1) Find the point of operation in the permanent state for both types of loads as well as stability using only the relationships of derivatives (slopes) 2) If the torque-inertia of the engine...
Given an input voltage of 120VAC (RMS) +/- 1% mains voltage with 60 Hz frequency (plugged into your wall), design a rectifier circuit that outputs +9V and -5V (account for diode voltage drop). The output voltages should be within +/- 5% of their specification (including peak-peak voltage ripple) with a load of up to 40 mA on the +9V supply and 20 mA on the -5V supply. (6 points) Show circuit diagram of design. For transformer, simply specify turns ratio(s)....
To design a high efficiency d.c., to d.c power converter with the given specifications min 10V max 15V nominal (regulated) 8V Input voltage: Output voltage: Nominal load current: 4A Inductor current ripple: 0.1A max Switching frequency: 30 kHz Output voltage ripple: 20 mV Define a suitable power circuit topology to meet the above specification? Sketch a circuit diagram of the chosen power circuit topology (a) Define the minimum and maximum duty cycles assuming that the control circuit keeps the output...
A shunt de motor is rated at 6kW, 120V and 1200 r/min has a magnetization curve as shown in Figure 1. The armature resistance is 0.189 and the field resistance is 2002 with and adjustable field resistance of 0 to 4002. The shunt de motor has rated line current of 50A when supplying rated voltage. (a) Determine the value of the adjustable field resistance so that the motor operates at no- load speed of 1200 r/min. [5 marks] (b) Assuming...