Problem # 3 Determine the voltage drop and the current through each resistor in a circuit...
QUESTION 1 5 points Save Answer A resistor R = 2k Ohms has a voltage V = 15 Volts. What is the current I through the resistor? Express your answer in mA. QUESTION 2 5 points Save Answer Three resistors are connected in series: R1 10k Ohms, R2 = 17k Ohms, R3 = 32k Ohms. A DC voltage source ( Volts) is connected across the three resistors. Determine the current I in mA. 7 QUESTION 3 5 points Save Answer...
(a) What is the current flowing through each resistor in a circuit consisting of a 48.0-V battery and a 24.0 Ω resistor connected in series with a 96.0 Ω resistor? (b) What is the voltage drop across each resistor? (c) What is the power dissipated in each resistor? (d) If the two resistors were connected in parallel rather than series, what would be the current flow through each resistor? (e) What would be the voltage drop across each resistor for...
When resistors are in series, each resistor has the same current but the voltage is different for each according to Ohm’s Law. A given circuit consists of two resistors in series connected to a 24.0-V battery. The current in the circuit is 0.0320 A. If R_1=250.0 Ω,and R_2=500.0 Ω. Find the potential difference across each resistor. Find the equivalent resistance. If the circuit in Problem 6 above is reconnected with the two resistors in parallel, the...
Three resistors of values 2 Ω, 6 Ω and 12 Ω are connected across a DC voltage source as shown in Figure 21-12. If the total current through the circuit is / 3.0 A, what is the current through the 12 Ω resistor? 0.3 A 0.4 A 0.2 A 0.6 A 0.5 A
What is the equivalent resistance in a circuit if the following resistors are connected in parallel. If a voltage source of 5 volts is connected into the circuit, what is the net current coming out of the voltage source. Resistor 1 = 15 ohms, Resistor 2 = 23 ohms, Resistor 3 = 40 ohms
4) Given the circuit below. The voltage is 5 volts and each resistor is 10 ohms. The current flowing through the circuit (when measured by an ideal ammeter) is 1 amp. a) Show current through the circuit is 1 A. Next, assume you put a DMM (in ammeter mode) which has a resistance of one ohm at point A. Recalculate the equivalent resistance of the circuit. b) What is the current flowing through the circuit now. This is the current...
voltage going through = 28 V resistance through entire circuit = 4 ohms a) What are the values of the three resistors below? b) what is the current and voltage drop across each of the 3 resistors below? ww
Help!Problem 12 (lab) Determine the equivalent resistance of the circuit, the current through each resistor, and the corresponding voltage drop. Simulate the circuit using PHET's Circuit Construction Kit: DC-Virtual Lab. https://phet.colorado.edu/en/simulation/circuit-construction-kit-dc-virtual-lab Determine the percent error in the current and voltage values obtained, treating the PHET values as experimental.
Using Matlab When several resistors are connected in an electrical circuit in parallel, the current through each of them is given by in=vs/Rnwhere in and Rn are the current through resistor n and its resistance, respectively, and vs is the source voltage. The equivalent resistance, Req, can be determined from the equation 1/Req=1/R1+1/R2+1/R3+.......+1/Rn. The source current is given by is , and the power, Pn, dissipated in each resistor is given by . is=vs/Req, and Pn=vsin. Write a program in...
A battery with a voltage of 16.0 V is connected to four resistors in the circuit shown above. The resistors are identical, each having a resistance of 8.00 ohms. What is the equivalent resistance of this set of four resistors? ohms Calculate the current through resistor C. A Which resistor has the most current through it, in this circuit? resistor A resistor B resistor C resistor D they all get equal currents, because the resistors are identical