ZuoTi.Pro
Question

Calculate SNR(dB) given a noise voltage specification of 500.5nV/sqrt(Hz), used over an audio frequency range of...

Calculate SNR(dB) given a noise voltage specification of 500.5nV/sqrt(Hz), used over an audio frequency range of 20Hz to 20kHz, with a voltage gain of 55dB. The output voltage is 1.75 V. Calculate the noise voltage specification given SNR(dB) = 150dB using the same output voltage, frequency range, and gain as in number 3.

engineering   Electrical-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

0 0
Add a comment
Know the answer?
Add Answer to:
Calculate SNR(dB) given a noise voltage specification of 500.5nV/sqrt(Hz), used over an audio frequency range of...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • Question 1 The noise floor, also known as additive white Gaussian noise (AWGN), is a continuous...

    Question 1 The noise floor, also known as additive white Gaussian noise (AWGN), is a continuous noise level that appears over a wide spectrum when viewed in the frequency domain. True False 10 points Question 2 When considering the impact of impulse noise, we find that it is more devastating to a digital communications link, than an analog one. Therefore, error control methods should be used on all digital links. True False 10 points Question 3 When two transmitters operate...

  • Exercise 6: Consider an audio signal with an amplitude that ranges over the interval [-10,10] and...

    Communication systems theory: Exercise 6: Consider an audio signal with an amplitude that ranges over the interval [-10,10] and with spectral components limited to the frequency band of 300 Hz to 3300 Hz. The signal is sampled at a rate of 8000 samples/second and used to generate a PCM signal. The signal-to-quantization- noise ratio (SQNR) is required to be maintained at 43.9 dB a) What is the minimum number of uniform quantization levels needed, and what is the minimum number...

  • 3. The following is the amplitude spectrum of a DSB+carrier AM signal x(f) 1.5 1.5 1.5 1.5 f (Hz)...

    3. The following is the amplitude spectrum of a DSB+carrier AM signal x(f) 1.5 1.5 1.5 1.5 f (Hz) 1920 2000 2080 2080 2000 1920 (a) (10 points) Determine the carrier frequency fe the carrier amplitude Ac the mod ulation index ,, and the message signal m(t) of the AM signal. (b) (10 points) Given that μ2Sm 0.18, find the output SNR (in dB) if the received signal includes white noise with a power spectral density of η/2-10-10 W/Hz. (c)...

  • Given an input voltage of 120VAC (RMS) +/- 1% mains voltage with 60 Hz frequency (plugged...

    Given an input voltage of 120VAC (RMS) +/- 1% mains voltage with 60 Hz frequency (plugged into your wall), design a rectifier circuit that outputs +9V and -5V (account for diode voltage drop). The output voltages should be within +/- 5% of their specification (including peak-peak voltage ripple) with a load of up to 40 mA on the +9V supply and 20 mA on the -5V supply. (6 points) Show circuit diagram of design. For transformer, simply specify turns ratio(s)....

  • A voltage signal is created by adding the output from a white noise generator and from...

    A voltage signal is created by adding the output from a white noise generator and from a sinewave generator. The white noise is band limited in the range 30 to 80 Hz and has a root mean square value (rms) of 1.5 V. The sine wave has a frequency of 50 Hz and an amplitude of 1.0 V. The signal is digitized at 200 samples per second and a spectral density is obtained by the Fast Fourier Transfer (FFT) algorithm,...

  • Need help with schematics for blocks 3, 4 and 5!!!!!! Include all schematics and wiring along with the component values...

    Need help with schematics for blocks 3, 4 and 5!!!!!! Include all schematics and wiring along with the component values and how you acquired them. Explain how each block functions and label any figures. Need schematics for blocks 3, 4 and 5!!!!!! Goal For your final project you will be asked to design and assemble a system in which you will input a stereo audio signal, mix the channels into a single mono signal, amplify the signal, filter it to...

  • A. (10 pts) Implement the voltage amplifier shown below using an ideal op amp circuit. You have o...

    a. (10 pts) Implement the voltage amplifier shown below using an ideal op amp circuit. You have one op amp available for this circuit, and a range of resistors with values from 1 kΩ to 100 ka. Draw the schematic of your op amp circuit, labeling resistor values. Make sure the gain, input resistance, and output resistance of your circuit matches the model in the schematic. R=012 *100v, RL 100 b. (5 pts) Your amplifier circuit should have a frequency...

  • (a) Calculate the range of wavelengths (in m) for AM radio given its frequency range is...

    (a) Calculate the range of wavelengths (in m) for AM radio given its frequency range is 540 to 1,600 kHz. smaller value larger value Assume the mostly infrared radiation from a heat lamp acts like a continuous wave with wavelength 1.50 pm. (a) If the lamp's 385-W output is focused on a person's shoulder, over a circular area 26.0 cm in diameter, what is the intensity? W/m2 (b) What is the peak electric field strength? V/m (c) Find the peak...

  • 250 mH Vi Given: The circuit shown above operates in steady state over a range of...

    250 mH Vi Given: The circuit shown above operates in steady state over a range of frequencies. Vj is the input voltage and Vo is the output voltage. a. Determine the resistance value in K2 for which the half-power frequency, ??.s 10 krad/s. b. Using the value of R found in part a, determine the radian frequency (01 at which Vo lags V, by 40 c. Is this a High-pass or a Low-pass filter? Solution R= krad/s, and the filter...

  • 2. a. Find Eb/No and Amplitude A required to give Pb 10-5 for the following coherent digital modu...

    2. a. Find Eb/No and Amplitude A required to give Pb 10-5 for the following coherent digital modulation schemes if No-10-5 and time is 0.5msec i. On-Off keying (ASK), ii. BPSK, iii. BFSK and v. BPSK with a phase error of 5 deg. Consider an audio signal with spectral components limited to the frequency band 300 to 3300 Hz. Assume that the sampling rate of 8000 samples/s will be used to generate a PCM signal. The ratio of peak signal...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT