ZuoTi.Pro
Question

What is the recommended feed rate for drills over 1 inch in diameter?

What is the recommended feed rate for drills over 1 inch in diameter?

engineering   Civil-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

0 0
Add a comment
Know the answer?
Add Answer to:
What is the recommended feed rate for drills over 1 inch in diameter?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • 1. Determine the proper speed and feed for a 4" diameter side cutter (HSS) with 16...

    1. Determine the proper speed and feed for a 4" diameter side cutter (HSS) with 16 teeth milling aluminum. Information available: Recommended cutting speed for aluminum (midpoint on range) = Recommended feet per tooth (midpoint on range) = Cutter diameter = 4" Number of teeth on cutter = 16

  • 1o. If a 20 inch long, 2 inch diameter stainless steel bar is to be turned down to 1 inch diamete...

    1o. If a 20 inch long, 2 inch diameter stainless steel bar is to be turned down to 1 inch diameter on a lathe, select V, f , and find N, MRR, Tm, HP, and HP assuming the efficiency of the motor to be 80%. 1o. If a 20 inch long, 2 inch diameter stainless steel bar is to be turned down to 1 inch diameter on a lathe, select V, f , and find N, MRR, Tm, HP, and...

  • A 0.24 inch diameter hole is punched in the bottom of a 1.5 inch diameter can....

    A 0.24 inch diameter hole is punched in the bottom of a 1.5 inch diameter can. The can is open at the top and contains 24 oz of liquid. What is the initial velocity of the liquid coming out of the hole?

  • An orifice meter with a 2 inch diameter opening is used to measure the flow rate...

    An orifice meter with a 2 inch diameter opening is used to measure the flow rate of water through a horizontal 3 inch diameter pipe. A mercury manometer is used to measure the pressure difference across the orifice. If the differential height of the manometer is 7 inches, determine the volumetric flowrate (gal/min) of water through the pipe. You may assume the discharge coefficient is 0.6.

  • 1. A constriction meter in a 2-inch diameter pipeline consists of a short section of 1.2-inch...

    1. A constriction meter in a 2-inch diameter pipeline consists of a short section of 1.2-inch diameter pipe (as shown below). The contraction and expansion are abrupt with 0 = 180 degrees. When the flow rate is 0.19 cfs the pressure at point 1 is 14 psi. (a) For this flow rate, calculate the level of the energy grade line (EGL) and hydraulic grade line (HGL) before the contraction (point 1), in the contraction (point 2) and after the expansion...

  • A submersible pump can maintain a flow rate of 46.0 gal/min through a 1.5 inch diameter...

    A submersible pump can maintain a flow rate of 46.0 gal/min through a 1.5 inch diameter pipe, provided the vertical change of the flow is less than 5 feet. What is the flow rate in m3/s? (use 1 m3 = 264 gal) What is the fluid speed in the pipe? (use 1.0 inch = 2.54 cm) What pressure change would occur in this pipe while moving water vertically upwards to a height of 4.0 meters while maintaining a constant flow...

  • A plate with a thickness of 1/2-inch is supported by a 9/16-inch diameter bolt and bracket...

    A plate with a thickness of 1/2-inch is supported by a 9/16-inch diameter bolt and bracket shown. If the load on the plate is 4150 lb, determine the bearing stress on the bolt applied by the plate. (2 points) bracket 9/16-in.-diameter bolt 1/2-in plate 4150 lb

  • A 3.00 inch diameter workpiece that is 25 in long is to be turned down to...

    A 3.00 inch diameter workpiece that is 25 in long is to be turned down to n2.384 inches. Process Specifications: a) Cutting Speed (V) = 300 ft/min, b) Feed (f) = 0.015 in/rev c) Depth of cut (d) = 0.044 in The bar will be held in a chuck and supported on the opposite end in a live center. With this work-holding setup, one end (15 inches) must be turned to diameter; then the bar must be reversed to turn...

  • If the air in a 12-inch diameter duct with an air flow of 1,500 ft3/min and...

    If the air in a 12-inch diameter duct with an air flow of 1,500 ft3/min and a velocity of 14 ft/min flows into a 6-inch diameter duct, what are the new flow rate and velocity? What velocity of air would be required to draw toxic vapors into a duct 24 inches away from a 12 inch round duct with an air flow rate of 1,500 ft3/min? Compare the flow rates into a hood that needs to capture a contaminant at...

  • .Suppose you want to drill a 2-in. thick plate of cast steel (0.4%C), 4-in. diameter hole....

    .Suppose you want to drill a 2-in. thick plate of cast steel (0.4%C), 4-in. diameter hole. An indexable HSS insert drill has been selected. Consider the table below, select the appropriate cutting speed, feed rate. Calculate the spindle speed (rpm), the feed rate (in/min), the MRR, and cutting time. Assume the cutting process will be performed in3 steps using 3 drills sizes in sequence 1”, then 2”, then 4”. Calculate the cutting total cutting time, considering a proper allowance each...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT