100 lb of R22 are in a thermodynamic cycle, consisting of the following process
Process 1-2: isobaric compression from P1=340 psia y T1=215 °F until saturated vapor
Process 2-3: constant volume cooling until T3= 120 °F
Process 3-4: isobaric expansion
Process 4-1: isochoric heating
Complete the tables and write if it's a power cycle or a refirgeration cycle
State | P (psia) | T(°F) | V(ft3/lb) | U(Btu/lb) |
1 | 340 | 215 | ||
2 | ||||
3 | 120 | |||
4 |
Process | Q(Btu) | W(Btu) |
ΔU(Btu) |
1-2 | |||
2-3 | |||
3-4 | |||
4-1 | |||
Total |
100 lb of R22 are in a thermodynamic cycle, consisting of the following process Process 1-2:...
A gas undergoes a thermodynamic cycle consisting of three processes:Compression occurs in Process 1-2 with pV= constant. P₁=10⁵ Pa, V₁=1.5 m³, and V₂=0.4 m³. U₂-U₁=0Process 2-3 is isobaric.Process 3-1 is isochoric. U₃-U1=-3259 kJa. Sketch the cycle on a p-V diagram.b. Calculate the heat transfer for Process 3-1.c. Calculate the work for process 2-3.
A system consisting of 1.0 kg of water and undergoes a thermodynamic power cycle composed of the following four processes: Process 1 – 2: Constant pressure heating at 1 MPa from saturated vapor Process 2 – 3: Constant volume cooling to pz = 500 kPa, Tz = 160°C Process 3 – 4: Isothermal compression with Q34 = -815.8 kJ Process 4-1: Constant volume heating (a) Sketch the cycle on T - v and p - v diagrams. (b) Is this...
Air in a piston-cylinder undergoes a cycle with the following processes: Process 1-2: Isobaric process from P = 0.1 MPa, T1 = 600K to T2 = 1200K Process 2-3: Isothermal process to state 3 where P3 = 0.05 MPa Process 3-4: Isochoric process to state 4 where P4 = 0.031 MPa Process 4-1: Polytropic process back to state 1 (a) Show the processes in a P-V plot showing the values. Also calculate or state the values of P. V. T...
2. Ideal Rankine cycle. The condenser pressure is 4 psia. Steam goes into turbine at 1100F and 1300 psia. The mass flow rate of steam is 2,000,000 lb/h. Cooling water from a lake flows through the condenser at 95,000,000 lb/hr and comes into the condenser at 63F. Determine: a) The net power made (BTU/h) b) Rate of heat transfer in the condenser (BTU/h) c) Overall thermal efficiency (%) d) The outlet temperature of the cooling water (F)
A Student cycle engine is analyzed using the cold air-standard method. Given the definition of each process in the cycle, determine the thermal efficiency of the engine for each set of defined ratios listed below. All ratios are given as the larger value over the smaller one. --Given Values-- Process 1-2 = Isentropic compression & volume ratio=rv12 Process 2-3 = Isobaric compression & volume ratio=rv23 Process 3-4 = Isometric heat addition & temperature ratio=rT34 Process 4-5 = Isobaric heat addition...
Please show solutions to part (b), (c), and (d). Thank you. A system consisting of 1.0 kg of water and undergoes a thermodynamic power cycle composed of the following four processes: Process 1 – 2: Constant pressure heating at 1 MPa from saturated vapor Process 2 – 3: Constant volume cooling to p3 = 500 kPa, T3 = 160°C Process 3 – 4: Isothermal compression with Q34 = -815.8 kJ Process 4 – 1: Constant volume heating (a) Sketch the...
A sketch of set of four processes involved in a closed thermodynamic system is shown in the adjoining pressure- volume diagram. Isothermal expansion brings 220 grams of a fluid from 415 kPa to a final pressure of 115 kPa and specific volume of 120 litres/kilogram. A reversible cooling process takes place at constant pressure with a work done of 525 Joules and then followed by a constant volume until the pressure of the fluid becomes 62 kPa. A Polytropic compression...
A gas within a piston-cylinder assembly undergoes a thermodynamic cycle consisting of three processes: Process 1-2: Constant volume V1 = 2 m3, p1 = 1 bar, to p2 = 3 bar, U2 – U1 = 400 kJ. Process 2-3: Constant pressure compression to V3 = 1 m3. Process 3-1: Adiabatic expansion, with W31 = 150 kJ. There are no significant changes in kinetic or potential energy. Determine the net work for the cycle, in kJ, and the heat transfers for...
2. One lb of air undergoes a power cycle consisting of the following processes: 1->2: constant volume from p1=20 psi, T1=500°R to T2=820°R 2->3: adiabatic expansion to v3 = 1.4 v2 3->1: constant pressure compression Sketch the cycle on a p-v diagram. Assuming ideal gas behavior, determine (a) The pressure at state 2 in psi. (b) The temperature at state 3 in °R. (c) The thermal efficiency of the cycle.
One pound of oxygen O2 undergoes a power cycle consisting of the following processes: 3.145 One lb of oxygen, 02, undergoes a power cycle consisting of the following processes: Process 1-2: Constant-volume heating from P1 = 20 lbf/in. 7, = 500°R to T2 = 820°R. Process 2-3: Adiabatic expansion to = 1.432 Process 3-1: Constant-pressure compression to state 1. Sketch the cycle on a p-v diagram. Assuming ideal gas behavior, determine (a) the pressure at state 2, in lbf/in.2 (b)...