A rod made of copper with resting length 2 m and area of 0.1 m^2 is...

Question

Question

A rod made of copper with resting length 2 m and area of 0.1 m^2 is stretched by 1mm. What

is the force on the end of the rod? What if it’s made of diamond?

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

A copper rod has a length of 1.5 m and a cross-sectional area of 4.8 ×...

A copper rod has a length of 1.5 m and a cross-sectional area of 4.8 × 10-4 m2. One end of the rod is in contact with boiling water and the other with a mixture of ice and water. What is the mass of ice per second that melts? Assume that no heat is lost through the side surface of the rod. GIve answer in kg/s.
A copper rod has a length of 2.0 m and a cross-sectional area of 3.4 x...

A copper rod has a length of 2.0 m and a cross-sectional area of 3.4 x 10-4 m2. One end of the rod is in contact with boiling water and the other with a mixture of ice and water. What is the mass of ice per second that melts? Assume that no heat is lost through the side surface of the rod. m/t = i
A copper rod and an aluminum rod of the same length and cross-sectional area are attached...

A copper rod and an aluminum rod of the same length and cross-sectional area are attached end to end. The copper end is placed in a furnace which is maintained at a constant temperature of 292∘C. The aluminum end is placed in an ice bath held at constant temperature of 0.0∘C. Calculate the temperature (in degrees Celsius) at the point where the two rods are joined. The thermal conductivity of copper is 380 J/(s⋅m⋅C∘) and that of aluminum is 200...

A copper rod and an aluminum rod of the same length and cross-sectional area are attached...

A copper rod and an aluminum rod of the same length and cross-sectional area are attached end to end (Figure 1). The copper end is placed in a furnace maintained at a constant temperature TCu = 230 ∘C . The aluminum end is placed in an ice bath held at a constant temperature of 0.0∘C. Calculate the temperature at the point where the two rods are joined.
A metal rod (weight = 100 N) is resting on a skateboard and leaning against a...

A metal rod (weight = 100 N) is resting on a skateboard and leaning against a wall (as in the figure). The skateboard would be free to roll except that it is attached to the wall with a spring (k= 1000 N/m), which happens to be stretched by 2.5 cm beyond its relaxed length. Assume the wall exerts no friction force on the rod, but that there is friction between the rod and the skateboard. Use the drop-down lists to...
2) Below is a rod of length 1 m made of a new steel alloy (E...

2) Below is a rod of length 1 m made of a new steel alloy (E - 200 GPa) which is constrained by tw fixed-fixed supports. The rod has an area of cross sectional area of 100 mm2. There are no residual stresses in the rod. Then, a force of 50 kN is applied to the rod at the location shown. Determine the reactions at the supports A and B. Now, suppose you want to reduce reaction at A and...

5) A copper rod (length L, mass m) slides with speed v over a U-shaped wire...

5) A copper rod (length L, mass m) slides with speed v over a U-shaped wire inside a constant magnetic field (B). The loop has resistance R. a) Find the magnitude and direction of the induced current in terms of the given quantities and constants. (HINT 1: Area = x L). b) Find the force vector of the copper rod.
Two rods, one made of brass and the other made of copper, are joined end to...

Two rods, one made of brass and the other made of copper, are joined end to end. The length of the brass section is 0.160 m and the length of the copper section is 0.640 m. Each segment has cross-sectional area 0.00680 m². The free end of the brass segment is in boiling water and the free end of the copper segment is in an ice and water mixture, in both cases under normal atmospheric pressure. The sides of the...
A steel wire of length 29.0 m and a copper wire of length 25.0 m, both...

A steel wire of length 29.0 m and a copper wire of length 25.0 m, both with 1.00-mm diameters, are connected end to end and stretched to a tension of 132 N. During what time interval will a transverse wave travel the entire length of the two wires? (The density of steel and copper are 7860 and 8920 kg/m3, respectively.) s

Ice and COPPER STEEL water water A copper rod and a steel rod are joined to-...

Ice and COPPER STEEL water water A copper rod and a steel rod are joined to- gether as shown. Both have a cross sectional area of 4.0cm2. Both rods are insulated so that heat can be conducted only along their length. One end of the copper rod is immersed in boil- ing water, and one end of the steel rod is im- 65.0°C mersed in a mixture of ice and water 0°C. The temperature at the junction point is stable...