A physics student had determined the voltage with a DMM to be 1.08 V and a current of 9 mA with the Keithly meter.
What is the value of the resistor in the circuit? Give your answer in ohms.
Hope it helps...
Please give me a thumbs up...
And comment if you have any doubts..
A physics student had determined the voltage with a DMM to be 1.08 V and a...
Why can the internal resistance of the DMM can be determined without taking into account the 100 Ω resistor? Could this be done for a resistor of any resistance value? Explain your answer. A 500 μF capacitor is wired in series with a 5 V battery and a 20 kΩ resistor. What is the voltage across the capacitor after 20 seconds of closing the circuit? Show all calculations in your answer.
In the circuit shown above, a battery with a voltage ?Vbat = 24 V is connected to the circuit with resistances R1 = 5 Ohms, R2 = 35 Ohms, and R3 = 32 Ohms. The volt meter measures the potential difference between the points A and B, ?VAB. What is the power lost in the resistor R3? Give your answer in Watts to three signficant digits. Do not include units in your answer.
QUESTION 1 5 points Save Answer A resistor R = 2k Ohms has a voltage V = 15 Volts. What is the current I through the resistor? Express your answer in mA. QUESTION 2 5 points Save Answer Three resistors are connected in series: R1 10k Ohms, R2 = 17k Ohms, R3 = 32k Ohms. A DC voltage source ( Volts) is connected across the three resistors. Determine the current I in mA. 7 QUESTION 3 5 points Save Answer...
4) Given the circuit below. The voltage is 5 volts and each resistor is 10 ohms. The current flowing through the circuit (when measured by an ideal ammeter) is 1 amp. a) Show current through the circuit is 1 A. Next, assume you put a DMM (in ammeter mode) which has a resistance of one ohm at point A. Recalculate the equivalent resistance of the circuit. b) What is the current flowing through the circuit now. This is the current...
30%te Q1.- Using a 3% digits DMM and a VOM to measure a 12V voltage source and the results are recorded in the following Table 1:4 VOM 12.1ve 11.9ve 12.2ve 11.5ve 11.8V DMM 12.02ve 11.97ve 11.98ve 12.04ve 11.95ve Tahle Accuracy of the meter: VOM (+0.5% of 50V full-scale reading) DMM (0.3% of reading + 1 digit) Tahle 1 (1) Draw the circuit diagram with the voltmeter connected. (ii) Compare the two sets of data in Table 1 in terms of...
Q1. You are given a 12 V DC power supply. You are expected to develop a voltage divider to achieve a voltage of nominal 5V value using a pair of resistors from the E 12 range, with the restrition that you are not expected to draw a current of more than 1 mA from the 12 V DC supply i. Develop a simple circuit showing the possible values for each resistor pair, and the range of the DC output possible...
1. An amplifier has a voltage gain Av equal to 20. An input voltage v of 150 mVs applied to the input of the amplifier. What is the output voltage vo? Rs 2. For the amplifier in Problem 3, assume the input current i is 2 mA, and the output current io is 10 mA. What is the current gain A, ? Assuming the amplifier as described above has an output resistance is 0 ohms, what is the load resistance...
A battery with a voltage of 16.0 V is connected to four resistors in the circuit shown above. The resistors are identical, each having a resistance of 8.00 ohms. What is the equivalent resistance of this set of four resistors? ohms Calculate the current through resistor C. A Which resistor has the most current through it, in this circuit? resistor A resistor B resistor C resistor D they all get equal currents, because the resistors are identical
PI : For circuit below v-20 V and R,-8 Ohm and R2-2 Ohm. Calculate voltage and power loss in each resistor in the circuit. (Use voltage division and P = (voltage*voltage) resistance)- You cannot use KVL, KCL or Ohms law) Ri R2 P2: For circuit below i = 50 A and R1 = 15 Ohm and R2 = 10 Ohm. Calculate current and power loss in each resistor in the circuit. (Use current division and P - (current*current) resistance) You...
Review Constan Consider the circuit of the figure (Figure 1). Part A If the voltage across the 30- k2 resistor is measured with a 50-kN2 voltmeter, what does the meter read? Express your answer to two significant figures and include the appropriate units. μΑ. ? V50 kn = Value Units Submit Request Answer Part B If the voltage across the 30-k2 resistor is measured with a 250-k voltmeter, what does the meter read? Express your answer to two significant figures...