How does microfiltration work in industrial milk processing? is it through pump or is it through the filter spread out and the milk content pour through the filter from the top?
Solution :
Yes microfiltration work through the filter spread out and the milk content pour through the filter from the top. It is a low pressure- driven membrane filtration process, which is based on a membrane with an open structure allowing dissolved components to pass through the filter spread while most non-dissolved components are rejected by the membrane.
Thank you
Wish you all the best buddy ?? please upvote it ?
How does microfiltration work in industrial milk processing? is it through pump or is it through...
4 years ago, you purchased an industrial pump for your chemical processing plant, The pump was purchased for $3,900, The pump was expected to depreciate at a rate of 20%, using the declining balance method, Today, you sold the pump for $7,100, Given that 50% of capital gains are taxable, and that the corporate income tax rate 15 43%, what are your after-tax proceeds from the sale of the pump? Assume no capital losses are available, and that the HYR...
Your heart does work to pump blood through your body. Each minute, 5.0 L of blood travels through your circulatory system. The pressure drops from 16 kPa as it exits the heart to approximately zero as it returns to the heart. We can calculate the work required to move a fluid volume V through a pressure difference with a formula very similar to the one you saw for work in gases. Part A What is the work done to pump...
The Shady Farm Milk Company can process milk at a fixed rate of 6800 gallons/hour. The company’s clients request 107000 gallons of milk over the course of one day. This demand is spread out uniformly from 8 a.m. - 6 p.m. The company starts producing at 8 a.m. and continues to work until all of the demand has been satisfied. How long does the client requesting milk at 6pm have to wait to have their _____ hours demand satisfied? (round...
Set up and solve an integral for the amount of work needed to
draw up all the milk through a straw.
4. Suppose a 5 cm tall bowl is made from the bottom part of a sphere of radius 12 cm (as shown to the right), and it is filled to the top with milk. Find the amount of work done by a child that drinks all the milk through a straw if the top of the 2 cm straw...
Weston Products manufactures an industrial cleaning compound that goes through three processing departments-Grinding, Mixing. and Cooking All raw materials are introduced at the start of work in the Grinding Department. The Work in Process T-account for the Grinding Department for May is given below:
Please show all work . Every step .
5. How much work is required to pump the water out of the top of a half-full 10 foot long horizontal cylindrical tank that has radius 3 ft? The weight density of the water is 62.4 %, Round to a whole number. (Sec. 8.4) (2 points)
How much work is required to pump the water out of the top of a half-full 10 foot long horizontal cylindrical tank that has radius 3 ft. ? The weight density of the water is 62.4 lb/ft3. Round to a whole number. ANSWER IS 37,697. Please write out every step.
A pump circulates water through a system of connected pipes on a house from the basement to the top floor. The pump is located in the basement and drives water at 3.93m/s through a 6.99 cm diameter pipe at a gauge pressure of 425000 Pa. What will be the pressure (in kPa) in a 3.19 cm diameter pipe on the top floor, 21.6 m above the pipe? Please show work!
Weston Products manufactures an industrial cleaning compound that goes through three processing departments Grinding, Mixing, and Cooking. All raw materials are introduced at the start of work in the Grinding Department. The Work in Process T-account for the Grinding Department for May is given below: Work in Process Grinding Department Completed and transferredInventory, May 121,800to the Mixing DepartmentMaterials133,400Conversion225,500Inventory, May 1?The May 1 work in process inventory was 100% complete with respect to materials and 30% complete with respect to conversion. During May,...
In general how does the processing of thermoplastics into the desired shape differ from the processing of thermosetting plastics?