24. from A water main is to be laid The water level in the tower is 150 ft above the ground. The ...

Question

Question

24. from A water main is to be laid The water level in the tower is 150 ft above the ground. The main must supply a maximum o

engineering Civil-Engineering

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

tou) or .to ubdį vieio。. a iven data mi le 0 1 良 o.433 30 12dG 39 2 R. 5518 11. 8o

Add a comment

Answer 2

Similar Homework Help Questions

24. from A water main is to be laid The water level in the tower is 150 ft above the ground. The ...

24. from A water main is to be laid The water level in the tower is 150 ft above the ground. The main must supply a maximum of 1000 gpm with a minimum of 5psig at the discharge end, at a temperature of 65°F. What size commercial steel sch 40 pipe should be used for the water main? If plastic pipe (which is hydraulically smooth) were used instead, would this alter the result? If so, what diameter of plastic pipe...
Water is pumped from a well to a water tower (an above-ground reservoir) through a 330...

Water is pumped from a well to a water tower (an above-ground reservoir) through a 330 ft long galvanized iron pipe (ε-0.0005 ft) with a 2-in diameter. The water surface in the well is 10 ft below the ground and the water surface in the tower is 60 ft above the ground. The water is to be delivered at a rate of at least 370 L/min. The sum of the minor loss coefficients is 2.1 a) Using the pump performance...
A pump delivers water at 200C between a reservoir and a water tank that is 75[ft] higher than the...

A pump delivers water at 200C between a reservoir and a water tank that is 75[ft] higher than the reservoir. The suction side of the system consists of a cast iron pipe of 1[ft]diameter with a strainer (Ks= 2.5) and four 90-degree bends at R/D= 5. The discharge side of the system includes a 1000[ft] long commercial steel pipe with 12” diameter followed by a gate valve. The NPSH required for the pump is 10[ft], and the design discharge is...

Vent 10 ft Fully open globe valve (KL = 10) TT 6 ft 1500 ft with...

Vent 10 ft Fully open globe valve (KL = 10) TT 6 ft 1500 ft with 15 (including the one shown) 90° elbows (K1 = 1.5) For the water tower shown above, the pressure at section (2) should not fall be- low 50 psi. The top of the water tower is vented to the open air, and all pipes are smooth 6-in. diameter plastic (€/D –0). 4.1 (4 pts) For a pipe of this size, what is the maximum discharge...
(100 points) Water at 25°C is pumped at a rate of 0.075m'/s from a reservoir 20m above a pump to a free di...

(100 points) Water at 25°C is pumped at a rate of 0.075m'/s from a reservoir 20m above a pump to a free discharge (this means discharged to atmosphere) 35m above the pump. The pressure on the intake side of the pump is 150kPa and the pressure on the discharge side of the pump is 450kPa. The pipe between the reservoir and the pump is 3 meters of 5in diameter cast iron. From the pump to the discharge the pipe is...
4. A cast iron pipe is to carry 1000 GPM of water from a lake down...

4. A cast iron pipe is to carry 1000 GPM of water from a lake down a hill side where it will discharge into the atmosphere. The elevation change is 750 ft. and the pipe is 2250 ft. long. Neglecting minor losses what should be the diameter of the pipe? 748 gal -i t 5. and vertical forces on the wall and their moments about point B. The tank width into the page is 5 A. The fluid is water....

A centrifugal pump is used to pump water at 77ºF from a reservoir whose surface is 20 ft above th...

A centrifugal pump is used to pump water at 77ºF from a reservoir whose surface is 20 ft above the centerline of the pump inlet. The Pipe System consists of 67.5 ft of PVC pipe with a 1.2 in ID and negligible average internal roughness height. The length of the pipe from the bottom of the lower tank to the pump inlet is 12 ft. There are several minor losses in the pipe: an acute edge entry (KL = 0.5),...
I need just CONTROL VOLUME & ASSUMPTIONS 02. Water at 25 °C is circulated from a large tank, through a filter, a...

I need just CONTROL VOLUME & ASSUMPTIONS 02. Water at 25 °C is circulated from a large tank, through a filter, and back to the tank as shown in the figure below. The power added to the water by the pump is 271 W Determine the flow rate through the filter. In your solution, follow these steps: Summarize the problem by stating what is given and what needs to be determined State all your assumptions Show the control volume chosen...
(100 points) Water at 25°C is pumped at a rate of 0.075m's from a reservoir 20m above a pump to a free 1....

(100 points) Water at 25°C is pumped at a rate of 0.075m's from a reservoir 20m above a pump to a free 1. discharge (this means discharged to atmosphere) 35m above the pump. The pressure on the intake side of the pump is 150kPa and the pressure on the discharge side of the pump is 450kPa. The pipe between the reservoir and the pump is 3 meters of Sin diameter cast iron. From the pump to the discharge the pipe...

L 2. Steady statemass balance: Water is flowing at steady state in a 0.1 meter-diameter pipe...

L 2. Steady statemass balance: Water is flowing at steady state in a 0.1 meter-diameter pipe with a maximum velocity (turbulent profile) of 0.3 meters/sec. The pipe then goes through an expansion, to where it is then flowing in a 0.5 meter-diameter pipe, and the flow regime has changed from turbulent to laminar. In the second section of pipe, calculate the velocity as (a) block flow profile (Vavg), and (b) maximum velocity in laminar flow profile? HINT: you will need...

24. from A water main is to be laid The water level in the tower is 150 ft above the ground. The ...

Homework Answers