Homework Answers
Add Answer to:
Assume that the parameters of the V12 V transistors are K 0.2mAV VN - 2V and λ-0.02V-1. Determine...
For the differential amplifier shown in Figure 6: Assume well-matched transistors and = 100 for all transistors: a) Wh...
For the differential amplifier shown in Figure 6: Assume
well-matched transistors and = 100 for all transistors:
a) Why it is important to use well-matched transistors in
differential amplifier circuits? What is the potential influence of
mismatched transistors on the performance of the differential
amplifier?
b) Determine the resistor values (R1, R2 and R3) such that the
emitter coupled current IE = 0.5 mA and VC1 = 3 V.
c) Draw the ac equivalent circuit for the single ended...
December 2013 Elec-B5, Advanced Electronics QUESTION (1) In the following circuits, assume all transistors have the following parameters: K 0.5 mA/V2, VT,-1 V and λ-0.02. Given: 1M bias I mA M M2...
December 2013 Elec-B5, Advanced Electronics QUESTION (1) In the following circuits, assume all transistors have the following parameters: K 0.5 mA/V2, VT,-1 V and λ-0.02. Given: 1M bias I mA M M2 꼬 + 2 고 (~ 2 a) Estimate the differential gain vourlVIN in (V/V) b) Find the common mode input resistance Ricm c) Find the common mode input range. d) Estimate the common mode rejection ratio, CMRR. Express your result in dB. Useful formulae: for n-channel MOSFET (6...
3. Now, consider the MOSFET DA on Figure P1.3. Transistors Q5 and Q6 are n-channel MOSFETs with threshold voltages V,-V,-V-2 V and transconductance parameters k,-k,- k- 100 m/y2 Let lc, In, and I...
3. Now, consider the MOSFET DA on Figure P1.3. Transistors Q5 and Q6 are n-channel MOSFETs with threshold voltages V,-V,-V-2 V and transconductance parameters k,-k,- k- 100 m/y2 Let lc, In, and Is, be, respectively, the gate, drain, and source currents of Q5. Moreover, let aIn, and Is, be, respectively, the gate, drain, and source currents of Q6. DC analysis: Find the operating points (Qpoine)of both Q5 and Q6. AC analysis: (You can use the analysis by symmetry technique) vDifferential...
2. For the following amplifier, assume that all transistors are active and λ is nonzero. Find the gain V。/V, in terms of small-signal parameters. VD CAN1 Q13 3va 212 Q, -Vss 2. For the followin...
2. For the following amplifier, assume that all transistors are active and λ is nonzero. Find the gain V。/V, in terms of small-signal parameters. VD CAN1 Q13 3va 212 Q, -Vss
2. For the following amplifier, assume that all transistors are active and λ is nonzero. Find the gain V。/V, in terms of small-signal parameters. VD CAN1 Q13 3va 212 Q, -Vss
The 1 mA. V, ls -VE -15 15 V, in the following differential amplifier circuit, Vcc parameters are given as β, 100, VBE# 0.7 V, pr-25 mV, K.-100 V. transistor Rc-10 kΩ For: RE-150 Ω Rc Rc REE-200...
The 1 mA. V, ls -VE -15 15 V, in the following differential amplifier circuit, Vcc parameters are given as β, 100, VBE# 0.7 V, pr-25 mV, K.-100 V. transistor Rc-10 kΩ For: RE-150 Ω Rc Rc REE-200 kΩ a) What is the input differential resistance, Rid b) What is the overall voltage gain vV? You c) What is input common mode resistance, d) What is the worst case common mode gain that appear across the two input terminals? (4...
1. (a) Express the differential gain (double side) of the amplifier using TR parameters and Rc. (...
1. (a) Express the differential gain (double side) of the amplifier using TR parameters and Rc. (3pts) (b) Express the differential gain for a single side output. (2pts) (e) Design the Re such that o velve IV when vi5mV and v2+5mV (3pts) (d) Determine the maximum common-mode input voltage (5pts) (e) Determine the differential mode input resistance of the amplifier Beta is 100.(3pts) V+ = 10V R. ci C2 ei 02 2 t )10 = 2 mA V-=-10V
1. (a)...
SIM D *8.51 The differential amplifier in Fig. P8.51 utilizes a resistor Rss to establish a 1-mA ...
Please solve in details and in a clear way.
SIM D *8.51 The differential amplifier in Fig. P8.51 utilizes a resistor Rss to establish a 1-mA de bias current. that this amplifier uses a single 5-V supply and thus the de common-mode voltage Vcoy cannot be zero. Transistors and Q2 have k, W/L = 2.5 mA/V2, V, Note 0.7 V, and λ = 0. in (a) Find the required value of VeM ys: (b) Find the value of Rp that...
Assume, VAfor differential pair transistors. Which of the following statements is incorrect? CO7 57.2 k VO3 VO2 C2 01 E6 REF E6 C3 V15V 04 V 15 V The differential stage is biased by basic 3 transisto...
Assume, VAfor differential pair transistors. Which of the following statements is incorrect? CO7 57.2 k VO3 VO2 C2 01 E6 REF E6 C3 V15V 04 V 15 V The differential stage is biased by basic 3 transistor current course (with double emitter on its output) Ideally Vo3 should be at 0.7V so that it produces a 0 output when there is no differential mode input signal. Gain of Vo3 Vd is approximately equal to 1 since it acts as emitter...
Problem 3) The transistor parameters for the circuit are: B-200, VRE(Oon)- 0.7 V. and VA -80...
Problem 3) The transistor parameters for the circuit are: B-200, VRE(Oon)- 0.7 V. and VA -80 V. Determine the differential-mode voltage gain Ar /v4, the common-mode voltage gain AcmVo /Vem, Rid, Ricm, and CMRR. AdeVova 12--12)-0-7mA 1-7k v-12V O 12-8 4.6 R, z1.93mA R- 430 K Vo4 Vo Ad (-V)Acm -051)(8-) Aam4)9 ,44=G(Acm) v,o- 10.6 Te-1c201 ACm 0.192 O--12 V CmeR-aolag 0.87 0107 13.12 35
Problem 3) The transistor parameters for the circuit are: B-200, VRE(Oon)- 0.7 V. and VA...
Problem 1 (40 pts) Assume that the capacitors are large enough to be considered as short circuits...
Problem 1 (40 pts) Assume that the capacitors are large enough to be considered as short circuits at the frequencies of interest, β-100, and the Q-points for the three transistors (true or not) Mi, Q2, and Q3 are (0.2mA. 10.2V), (1.3mA. 7.1V), (2.2mA, 9.0V), respectively, and VA- +15 V c24.7k 15 kΩ 02 2.2 kΩ 250 Ω A] Determine the voltage gain of the middle stage of the amplifier shown above Vc2/Vb2. Assume E-IC Expression Value RL2 is the total...
For the differential amplifier shown in Figure 6: Assume
well-matched transistors and = 100 for all transistors:
a) Why it is important to use well-matched transistors in
differential amplifier circuits? What is the potential influence of
mismatched transistors on the performance of the differential
amplifier?
b) Determine the resistor values (R1, R2 and R3) such that the
emitter coupled current IE = 0.5 mA and VC1 = 3 V.
c) Draw the ac equivalent circuit for the single ended...
December 2013 Elec-B5, Advanced Electronics QUESTION (1) In the following circuits, assume all transistors have the following parameters: K 0.5 mA/V2, VT,-1 V and λ-0.02. Given: 1M bias I mA M M2 꼬 + 2 고 (~ 2 a) Estimate the differential gain vourlVIN in (V/V) b) Find the common mode input resistance Ricm c) Find the common mode input range. d) Estimate the common mode rejection ratio, CMRR. Express your result in dB. Useful formulae: for n-channel MOSFET (6...
3. Now, consider the MOSFET DA on Figure P1.3. Transistors Q5 and Q6 are n-channel MOSFETs with threshold voltages V,-V,-V-2 V and transconductance parameters k,-k,- k- 100 m/y2 Let lc, In, and Is, be, respectively, the gate, drain, and source currents of Q5. Moreover, let aIn, and Is, be, respectively, the gate, drain, and source currents of Q6. DC analysis: Find the operating points (Qpoine)of both Q5 and Q6. AC analysis: (You can use the analysis by symmetry technique) vDifferential...
2. For the following amplifier, assume that all transistors are active and λ is nonzero. Find the gain V。/V, in terms of small-signal parameters. VD CAN1 Q13 3va 212 Q, -Vss
2. For the following amplifier, assume that all transistors are active and λ is nonzero. Find the gain V。/V, in terms of small-signal parameters. VD CAN1 Q13 3va 212 Q, -Vss
The 1 mA. V, ls -VE -15 15 V, in the following differential amplifier circuit, Vcc parameters are given as β, 100, VBE# 0.7 V, pr-25 mV, K.-100 V. transistor Rc-10 kΩ For: RE-150 Ω Rc Rc REE-200 kΩ a) What is the input differential resistance, Rid b) What is the overall voltage gain vV? You c) What is input common mode resistance, d) What is the worst case common mode gain that appear across the two input terminals? (4...
1. (a) Express the differential gain (double side) of the amplifier using TR parameters and Rc. (3pts) (b) Express the differential gain for a single side output. (2pts) (e) Design the Re such that o velve IV when vi5mV and v2+5mV (3pts) (d) Determine the maximum common-mode input voltage (5pts) (e) Determine the differential mode input resistance of the amplifier Beta is 100.(3pts) V+ = 10V R. ci C2 ei 02 2 t )10 = 2 mA V-=-10V
1. (a)...
Please solve in details and in a clear way.
SIM D *8.51 The differential amplifier in Fig. P8.51 utilizes a resistor Rss to establish a 1-mA de bias current. that this amplifier uses a single 5-V supply and thus the de common-mode voltage Vcoy cannot be zero. Transistors and Q2 have k, W/L = 2.5 mA/V2, V, Note 0.7 V, and λ = 0. in (a) Find the required value of VeM ys: (b) Find the value of Rp that...
Assume, VAfor differential pair transistors. Which of the following statements is incorrect? CO7 57.2 k VO3 VO2 C2 01 E6 REF E6 C3 V15V 04 V 15 V The differential stage is biased by basic 3 transistor current course (with double emitter on its output) Ideally Vo3 should be at 0.7V so that it produces a 0 output when there is no differential mode input signal. Gain of Vo3 Vd is approximately equal to 1 since it acts as emitter...
Problem 3) The transistor parameters for the circuit are: B-200, VRE(Oon)- 0.7 V. and VA -80 V. Determine the differential-mode voltage gain Ar /v4, the common-mode voltage gain AcmVo /Vem, Rid, Ricm, and CMRR. AdeVova 12--12)-0-7mA 1-7k v-12V O 12-8 4.6 R, z1.93mA R- 430 K Vo4 Vo Ad (-V)Acm -051)(8-) Aam4)9 ,44=G(Acm) v,o- 10.6 Te-1c201 ACm 0.192 O--12 V CmeR-aolag 0.87 0107 13.12 35
Problem 3) The transistor parameters for the circuit are: B-200, VRE(Oon)- 0.7 V. and VA...
Problem 1 (40 pts) Assume that the capacitors are large enough to be considered as short circuits at the frequencies of interest, β-100, and the Q-points for the three transistors (true or not) Mi, Q2, and Q3 are (0.2mA. 10.2V), (1.3mA. 7.1V), (2.2mA, 9.0V), respectively, and VA- +15 V c24.7k 15 kΩ 02 2.2 kΩ 250 Ω A] Determine the voltage gain of the middle stage of the amplifier shown above Vc2/Vb2. Assume E-IC Expression Value RL2 is the total...
Most questions answered within 3 hours.
-
Deacon Corporation has provided the following financial data
from its balance sheet and income statement:
Year...
asked 8 minutes ago -
List and discuss at least three variables from everyday life for
which you expect the variable ...
asked 7 minutes ago -
A high-pass filter consists of a 1.60 μF capacitor in series
with a 125 Ω resistor....
asked 9 minutes ago -
A newly developed artificial intelligence has trouble
distinguishing hand-written numbers from hand-written alphabets.
There are pictures...
asked 26 minutes ago -
The carbonate ion CO3 2- has multiple resonance structures.
a. Draw them and assign the hybridization...
asked 19 minutes ago -
In doing an allocation for a basket purchase
Use the individual costs and the total market...
asked 27 minutes ago -
what were the social political and economic causes and impacts of
the late 19th century urban...
asked 25 minutes ago -
if the magnitude of a velocity vector is 10m/s and it
makes an angle of 45...
asked 27 minutes ago -
Which amino acid has a basic R group?
A) tyrosine
B) Isoleucine
C) Glutamic Acid
D)...
asked 39 minutes ago -
Is there the need for the government to have hackers. Please
share your thoughts.
asked 42 minutes ago -
Explain why you should not lose any LDH activity when you
centrifuge a crude sample at...
asked 51 minutes ago -
An AA battery (object), standing on end, is placed to the left
of a diverging lens...
asked 51 minutes ago