Problem #1 A long solid slab is moving at a speed of 1 m/s over three identical lubricated pads a...
In the arrangement of the figure, billiard ball 1 moving at a speed of 1.6 m/s undergoes a glancing collision with identical billiard ball 2 that is at rest. After the collision, ball 2 moves at speed 0.8 m/s, at an angle of θ2 = 55°. mal li if (a) What is the magnitude of the velocity of ball 1 after the collision? m/s (b) What is its direction? o clockwise from the +x axis (c) Do the given data...
A bridge is supported by two types of rectangular cross-section piles located in a river as shown in Figure 1. The width of the piles is w - 0.5 m and their lengths are either l 2 m or 12 2.5 m. The river of depth of about 20 m runs at 2 m/s. Water density is p 1000 kg/m and its absolute viscosity 1.00 x 10-3 N.s/m2 You are asked to perform dimensional analysis to find the drag force...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
10:06 MW W 1) The drawing shows three identical springs hanging from the ceiling. Nothing is attached to the first spring. The second spring has a block with a weight of 4.5 N hanging from it. The third spring has a block with an unknown weight hanging from it. Find: A) The spring constant k. (2 points) 40.04 B) The weight of the unknown object. (2 points) 500 - 2) A pendulum has a length of 3.5 meters. Find the...
a) A workpiece (φ-75 mm, 1 275 mm) is machined using turning at a feed rate of 0.25 mm/rev. At a cutting speed- 3.5 m/s, the turning tool is ineffective after machining 3 parts, and at a cutting speed = 2.5 m/s, the turning tool is effective for producing 20 parts. Calculate the Cutting Speed that will allow 30 parts to be machined between tool changes [20 marks] b) An aluminium alloy workpiece (tensile strength - 325 N/mm2 and yield...
A bridge is supported by two types of rectangular cross-section piles located in a river as shown in Figure 1. The width of the piles is w -0.5 m and their lengths are either lı- 2 m or l2-2.5 m. The river of depth of about 20 m runs at 2 m/s. Water density is p 1000 kg/m3 and its absolute viscosityH 1.00 x 10-3 N.s/m2. You are asked to perform dimensional analysis to find the drag force on the...
A bridge is supported by two types of rectangular cross-section piles located in a river as shown in Figure 1. The width of the piles is w = 0.5 m and their lengths are either 11-2 m or l2 2.5 m. The river of depth of about 20 m runs at 2 m/s. Water density is p 1000 kg/m3 and its absolute viscosityu- 1.00 x 10-3 N.s/m2. You are asked to perform dimensional analysis to find the drag force on...
A bridge is supported by two types of rectangular cross-section piles located in a river as shown in Figure 1. The width of the piles is w 0.5 m and their lengths are eitherl 2 m or 12 2.5 m. The river of depth of about 20 m runs at 2 m/s. Water density is ρ-1000 kg/m' and its absolute viscosityH-1 .00 x 103 N.s/m2 You are asked to perform dimensional analysis to find the drag force on the piles,...
Q6. (a) Three identical fatigue specimens (denoted A, B and C) are fabricated from a non-ferrous alloy. Each is subjected to one of the maximum- minimum stress cycles listed in Table 26 (the frequency is the same for all tests) Table 26 Specimen Omax (MPa) Omin (MPa) A +450 -150 +300 -300 +500 -200 Rank the three specimens in terms of their fatigue lifetimes (highest to lowest). Justify this ranking [5 marks] (b) A cylindrical tie rod of diameter 20...
Three questions. Thanks 1. One long wire carries current 12.0 A to the left along the x axis. A second long wire carries current 80.0 A to the right along the line (y = 0.280 m, z = 0). (a) Where in the plane of the two wires is the total magnetic field equal to zero? (b) A particle with a charge of −2.00 µC is moving with a velocity of 150î Mm/s along the line (y = 0.100 m,...