4.9 Determine R1 and R2 to obtain a zero quiescent output voltage for the circuit shown in Figure...
For the circuit shown below, let Vcc 9 V R2 RE-0.11 kQ, R1 3.6 k2. and R2 -5.6 kQ. The transistor parameters are β-200, VBE(on)-OTV, VA-100 V and VT = 0.026 V. (a) Determine the quiescent value of IEQ (b) Find the small-signal voltage gain Av Vo/vs (c) Determine the output resistance R, looking into output terminals Av= 0.5589 Ro-0.4688 Ω Ro-0.9118 Ω leQ- 23.76 mA Ra " 0.6538 Ω leo 39.52 mA A, 0.9938 For the circuit shown below,...
Please answer clearly 2. Consider the circuit shown in Figure 1. Determine values of Ri, R2, and Rc to provide the quiescent emitter current 1.5 mA and the quiescent collector to emitter voltage 5V. Assume β 100, Re-I㏀、Va= 200V, VBEon-0.7V, and VT= 25mV. R1 Rc Vcc に 10v R2 Re Figure 1: BJT biasing configuration 2. Consider the circuit shown in Figure 1. Determine values of Ri, R2, and Rc to provide the quiescent emitter current 1.5 mA and the...
can someone help me with part c mpt tope alswersol the sdme part of you willbe penalized for this. Question 1 1 pts For the circuit shown in Figure 6.49, let Vcc -9V.RE 0.11 kQ, R1 3.6 k2, R2 5.6k(2, and Rs -o Ω . The transistor parameters are β-200. VBE(On)-Q7V, VA - 100 V and VT 0.026 V.(a) Determine the quiescent value of lEQ. (b) Find the small-signal voltage gain Av-vo/vg (c) Determine the output resistance Ro looking into...
In the circuit shown in the figure, VA = VB = 10.0 and R1 = R2 = R3 = R4 = Rs = 50.0. Current Is flows up through Rs, and I5 = 0.0500 A. Determine the current 14 through R4. Assume the direction of positive current flow is downward through R4. mm VA 14 = A Determine the voltage V2 across R2. mm V2 = V w Determine the power P3 dissipated by R3. R P3 = W
C.la For the circuit of Figure 1, choose values for resistors R1, R2, and R3(all resistances must be greater than one Kilo ohm). Given that the voltage source Vs1 = 8V and Vs2 = 10V determine the output voltage Vout. C.1b For the same resistor values Ri, R2, and Rs you chose in part C.la Given that the voltage source Vsi = 8V and Vs2 = 10V, use Figure 2(a) to determine the output voltage Vout/ and Figure 2(b) to determine the output voltage Vout2. Discussion:...
The circuit shown in the figure below contains three resistors (R1, R2, and R3) and three batteries (VA, VB, and Vd). The resistor values are: R1=2 Ohms, R2=R3=8 Ohms, and the battery voltages are VA=25 V, V8=15 V, and Ve=20 V. When the circuit is connected, what will be the power dissipated by R3? Vc R1 VA V. R2 R3 O 0.75 W O 1.25 W 0 2.67 w 4.2 w O 5.5 W The circuit shown in the figure...
The figure shows a section of a circuit. The resistances are R1-2.1 Ω, R2-4.9 Ω, and R3-6.26. and the indicated current is: 6.0 A. The electric potential difference between points A and B that connect the section to the rest of the circuit is VA-VB 80 V. (a) Is the device represented by "Box" absorbing or providing energy to the circuit, and (b) at what rate? R2 Box Rs (b) Number Units
The circuit shown in the figure below contains three resistors (R1, R2, and R3) and three batteries (VA, VB, and Vc). The resistor values are: R1=2 Ohms, R=R3=4 Ohms, and the battery voltages are VA=25 V, V8=15 V, and Vc=20 V. When the circuit is connected, what will be the power dissipated by R1? Vc M R1 + VA VB - R2 R3 1.25 W 2.0W 12.5 W 6.25 W 8.13 W The circuit shown in the figure contains four...
The circuit shown in the figure below contains three resistors (R1, R2, and R3) and three batteries (VA, Vs, and Vc). The resistor values are: R1=2 Ohms, R2=R3=6 Ohms, and the battery voltages are VA=25 V, V8=15 V, and Vc=20 V. When the circuit is connected, what will be the power dissipated by R2? Vc R1 VA t: VB R2 mm LM R3 O 1.0 W O 2.0 W O 5.0 W O 6.0 W O 7.5 W