Please refer the following images for the solution.
8-C) As shown below water is pumped and sprayed through a nozzle into the atmosphere at 20 m/s at...
Water, with density of 1000 kg/m3 and kinematic viscosity of 1.0 x 10- m2/s, is pumped through a total length of 60 m of pipe from a lower reservoir to a higher reservoir. The inner diameter of the pipe is 30 cm. Both reservoirs are open to the atmosphere, and the water surface of the higher reservoir is 10 m above that of the lower reservoir. The entrance from the lower reservoir to the pipe is sharp-edged, and along the...
1. Water is pumped from a low reservoir to a high reservoir that is 20 m higher in elevation. The water is flowing at 1.5 m/s through a 305 mm internal diameter piping system. The water is at 18 degrees C. There are 1,000 m of piping, six standard 45 degree bends, two standard 90 degree bends, a branch flow tee, three gate valves, a swing check valve, a square inlet and a square outlet. The piping and valves are...
Q3 (40 pts): Water is pumped through a 60-m-long, 0.3-m-diameter pipe from a lower reservoir to a higher reservoir, which has a water surface 10 m above the lower one. When the pump adds 40 kW to the water the flowrate is 0.20 m/s. Assume the following coefficients of minor losses: • Entrance: Kentrance = 0.5 Exit: Kexit = 1 Each elbow: Kelbow = 1.5 • Valve: K= 6 Part A (20 pts) Determine the pipe roughness ε. Part B...
Oil (density = 910Kg/m3 and viscosity 3.1 x10-3 Pa-s) is pumped from an open tank to a pressurized tank held at 400KPa gauge. The oil is pumped from an inlet at the side of the open tank through a line of commercial steel pipe (inside diameter 0.8m) at a rate of 5x10-3 m3/s. The length of the straight pipe is 150 m, and the pipe contains 4 (90-degree) elbows and two globe valve half open. The level of the liquid...
lunzontal pipe and pump system in the following figure discharges 0.01583 m3/s. The gage pressure iust before the pressure is 400 The m/s2 losses between 20°C water at 57 m3/h 0 kPa and just after the pump the gage a. The pump inlet diameter is 9 cm and the outlet diameter is 3 em. Let g-9.81 pump is 12 o Pwater9 kg/m, Hwate0.001002 kgm-s) and Pat the two pressure points and the pump. But consider frictional losses at the 9-cm...
Water at 20°C flows at 0.08 m3/s through a pipe and is metered by a 12 cm diameter long-radius flow nozzle (d = 12 cm). If the pressure drop across the nozzle is 25 kPa, what is the diameter of the pipe (D)? Use: Pwater = 998 kg/m3; Hwater = 0.001 kg/m-s. Express your answer in centimeters (cm). D
Water is being pumped from a lower reservoir to an elevated tank as shown below. The pump is 80% efficient and rated at 200 kW. Determine the flow rate if the total head loss from point 1 to point 2 is 15 m. elev. 100 m 150-mm diameter pipe pump 180-mm diameter pipe elev. 50 m water
Water at 20 C flows through the 20-mm diameter galvanized iron pipe such that it discharges at C from the fully opened gate valve B at 0.003 m/s Pe 998 3 kg/m3 and 100(10 ) m2/s Use the Part A Determine the required pressure at A Include the minor losses of the four elbows and gate valve. Express your answer to three significant figures and include the appropriate units. equation市一1.8kg(#)1.11 + 3.7 Figure 1 of 1 PA: I Value Units...
Steam enters a nozzle at 400°C and 800 kPa with a velocity of 10 m/s, and leaves at 300°C and 200 kPa while losing heat at a rate of 24 kW. For an inlet area of 675 cm, determine the velocity and the volume flow rate of the steam at the nozzle exit. 2-m/s (Round to the nearest integer) m3/s (Round to two decimal places) 400 C 800 kPa Steam200 kPa 10 m/s 300 C
Problem 4 (50 points) water is discharged from a reservoir at a rate of 18.103 m2/s using two horizontal cast iron pipes nected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses associated with the connection...