Homework Answers
Add Answer to:
Bernoulli's Equation Assignment 58) A venturi meter is a device that uses a constriction in a flo...
Water flows through a Venturi meter with a pipe diameter of 10.0 cm and a constriction...
Water flows through a Venturi meter with a pipe diameter of 10.0 cm and a constriction diameter of 5.6 cm. The U-tube manometer is partially filled with mercury. Find the flow rate of the water in the pipe of 10.0 cm diameter if the difference in the mercury level in the U-tube is 3.0 cm. Answer in L/s
A Venturi meter is a device for measuring the speed of a fluid within a pipe....
A Venturi meter is a device for measuring the speed of a fluid within a pipe. The drawing shows a gas flowing at speed v2 through a horizontal section of pipe whose cross-sectional area is A2-0.0589 m2 The gas has a density of ρ-1.30 kg m3 The Venturi meter has a cross sectiona area of .ם 33m and has been substituted for a section of the larger pipe. The pressure difference between the two sections is P2 P1 154 Pa....
A Venturi meter is a device for measuring the speed of a fluid within a pipe....
A Venturi meter is a device for measuring the speed of a fluid within a pipe. The drawing shows a l lowing a speed through a horizontal section of pipe whose cross-sectional area is Az - 0.0793 m. The gas has a density of -1.Joka/m. The Ventun meter has a cross-sectional area of A - 0.0706m and has been substituted for a section of the larger pipe. The pressure difference between the two sections is P2P -191 PaFind (a) the...
A Venturi meter equipped with a differential pressure gage is used to measure the flow rate...
A Venturi meter equipped with a differential pressure gage is used to measure the flow rate of water at 15°C (p = 999.1 kg/m”) through a 5-cm- diameter horizontal pipe. The diameter of the Venturi neck is 3 cm, and the measured pressure drop is 5.1 kPa. Taking the discharge coefficient to be 0.98, determine the volume flow rate of water and the average velocity through the pipe. 5 cm 3 cm Differential pressure gage Is The volume flow rate...
A venturi meter was installed in a pipe to measure the flow of the water inside....
A venturi meter was installed in a pipe to measure the flow of the water inside. The inlet diameter of the venturi is 25.4mm and the throat diameter is 12.7mm. Determine the actual flow rate in gpm if the throat Reynolds number is 10^5. The density and viscosity of the fluid is 62.4 Ibm/ft^3 and 3.511kg/m-hr, respectively. The venturi coefficient of discharge is 0.95.( do include unit/s in your answer and use two decimal places)
Nominal diameter of the pipe : 0.25 inch Select Venturi diameter : 0.3 ст Select type...
Nominal diameter of the pipe : 0.25 inch Select Venturi diameter : 0.3 ст Select type of Venturi Tube : Welded Tube Process Fluid : Water Manometric Fluid : Carbon tetrachloride Experimental Data Venturi Diameter : 0.003 meter(s) Type of Venturi tube : Welded Tube Nominal Pipe Diameter : 0.25 inch Actual Pipe Diameter : 0.92 cm Process Fluid : Water Density of Process Fluid : 1000 kg per Cubic meter Viscocity of Process Fluid : 0.85 centiPoise Manometric Fluid...
Q8 A horizontal pipe 50 mm diameter is fitted with a venturi tube, which has a...
Q8 A horizontal pipe 50 mm diameter is fitted with a venturi tube, which has a throat diameter of 40 mm. The pipe carries water at a pressure of 30 kPa gauge and velocity 3 m/s upstream of the throat. Determine: a. The mass flow rate; b. The velocity at the throat C. The pressure at the throat ignoring head losses: d. The pressure at the throat if a head loss equal to 5% of the total head occurs as...
The figure shows a Venturi flow characterized by a a smooth contraction of the pipe diameter...
The figure shows a Venturi flow characterized by a a smooth contraction of the pipe diameter D, to a throat diameter D2. The Venturi flow meter is connected to a n-tube manometer at location A where the pipe diameter is D, and to the throat of the contraction at location E where the diameter is D2. Assuming that the density of the air inside the n-tube is negligible, use your knowledge on hydrostatics, continuity and Bernoulli equation to calculate the...
A vertical Venturi meter equipped with a differential U-tube manometer as shown in Figure , is...
A vertical Venturi meter equipped with a differential U-tube manometer as shown in Figure , is used to measure the flow rate of liquid propane at 10°C (p = 514.7 kg/m3) flowing through a 'd1' mm diameter vertical pipe. For a discharge coefficient of 'cd', determine the actual volume flow rate of propane through the pipe with the given data. Pipe dia., d1 = Throat dia., d2 = Vertical dist., Y1 = Vertical dist., Y2 = Disch. Coeff., Cd =...
Open with Google Docs ▼ Question 3 Calculate the flow rate of water in a pipe of 30 cm diameter placed in an inclined position where a venturi meter is inserted, having a throat diameter of 15...
Open with Google Docs ▼ Question 3 Calculate the flow rate of water in a pipe of 30 cm diameter placed in an inclined position where a venturi meter is inserted, having a throat diameter of 15 cm. The difference of pressure between the main and throat is measured by a liquid of s.g. 0.6 in an inverted U-tube which gives a reading of 30 cm. The loss of head between the main and throat is 0.2 times the kinetic...
A Venturi meter is a device for measuring the speed of a fluid within a pipe. The drawing shows a gas flowing at speed v2 through a horizontal section of pipe whose cross-sectional area is A2-0.0589 m2 The gas has a density of ρ-1.30 kg m3 The Venturi meter has a cross sectiona area of .ם 33m and has been substituted for a section of the larger pipe. The pressure difference between the two sections is P2 P1 154 Pa....
A Venturi meter is a device for measuring the speed of a fluid within a pipe. The drawing shows a l lowing a speed through a horizontal section of pipe whose cross-sectional area is Az - 0.0793 m. The gas has a density of -1.Joka/m. The Ventun meter has a cross-sectional area of A - 0.0706m and has been substituted for a section of the larger pipe. The pressure difference between the two sections is P2P -191 PaFind (a) the...
A Venturi meter equipped with a differential pressure gage is used to measure the flow rate of water at 15°C (p = 999.1 kg/m”) through a 5-cm- diameter horizontal pipe. The diameter of the Venturi neck is 3 cm, and the measured pressure drop is 5.1 kPa. Taking the discharge coefficient to be 0.98, determine the volume flow rate of water and the average velocity through the pipe. 5 cm 3 cm Differential pressure gage Is The volume flow rate...
A venturi meter was installed in a pipe to measure the flow of the water inside. The inlet diameter of the venturi is 25.4mm and the throat diameter is 12.7mm. Determine the actual flow rate in gpm if the throat Reynolds number is 10^5. The density and viscosity of the fluid is 62.4 Ibm/ft^3 and 3.511kg/m-hr, respectively. The venturi coefficient of discharge is 0.95.( do include unit/s in your answer and use two decimal places)
Nominal diameter of the pipe : 0.25 inch Select Venturi diameter : 0.3 ст Select type of Venturi Tube : Welded Tube Process Fluid : Water Manometric Fluid : Carbon tetrachloride Experimental Data Venturi Diameter : 0.003 meter(s) Type of Venturi tube : Welded Tube Nominal Pipe Diameter : 0.25 inch Actual Pipe Diameter : 0.92 cm Process Fluid : Water Density of Process Fluid : 1000 kg per Cubic meter Viscocity of Process Fluid : 0.85 centiPoise Manometric Fluid...
Q8 A horizontal pipe 50 mm diameter is fitted with a venturi tube, which has a throat diameter of 40 mm. The pipe carries water at a pressure of 30 kPa gauge and velocity 3 m/s upstream of the throat. Determine: a. The mass flow rate; b. The velocity at the throat C. The pressure at the throat ignoring head losses: d. The pressure at the throat if a head loss equal to 5% of the total head occurs as...
The figure shows a Venturi flow characterized by a a smooth contraction of the pipe diameter D, to a throat diameter D2. The Venturi flow meter is connected to a n-tube manometer at location A where the pipe diameter is D, and to the throat of the contraction at location E where the diameter is D2. Assuming that the density of the air inside the n-tube is negligible, use your knowledge on hydrostatics, continuity and Bernoulli equation to calculate the...
A vertical Venturi meter equipped with a differential U-tube manometer as shown in Figure , is used to measure the flow rate of liquid propane at 10°C (p = 514.7 kg/m3) flowing through a 'd1' mm diameter vertical pipe. For a discharge coefficient of 'cd', determine the actual volume flow rate of propane through the pipe with the given data. Pipe dia., d1 = Throat dia., d2 = Vertical dist., Y1 = Vertical dist., Y2 = Disch. Coeff., Cd =...
Open with Google Docs ▼ Question 3 Calculate the flow rate of water in a pipe of 30 cm diameter placed in an inclined position where a venturi meter is inserted, having a throat diameter of 15 cm. The difference of pressure between the main and throat is measured by a liquid of s.g. 0.6 in an inverted U-tube which gives a reading of 30 cm. The loss of head between the main and throat is 0.2 times the kinetic...
Most questions answered within 3 hours.
-
A resistor and the capacitor are used to control the timing in
the RC circuit of...
asked 8 minutes ago -
Five moles of monatomic ideal gas have initial pressure 2.50 ×
103 Pa and initial volume...
asked 9 minutes ago -
Living in a group could bring several disadvantages to an
individual. What are some of the...
asked 26 minutes ago -
Complete and balance the following reactions. In case of no
reaction occurring write NR.
Mix #1:...
asked 31 minutes ago -
If an economy consumes 75% of any increase in income, then an
increase in autonomous investment...
asked 35 minutes ago -
A shotputter throws the shot with an initial speed of 15.8 m/s
at a 38.0 ∘...
asked 50 minutes ago -
Debra and Merina sell electronic equipment and supplies through
their partnership. They wish to expand their...
asked 51 minutes ago -
How does a linear regression allow you to better estimate
trends, costs, and other factors in...
asked 59 minutes ago -
1. (15%) Describe the difference between a pull (Kanban), push
and CONWIP production systems.
asked 55 minutes ago -
QUESTION 5
The total area under the Z distribution curve is equal to:
a.
10
b....
asked 1 hour ago -
Using Python
The variables x and y refer to numbers. Write a code segment
that prompts...
asked 1 hour ago -
If
the coefficient of static friction between a box and the floor is
0.35 with what...
asked 1 hour ago