3. (35 points) For the joint below, determine the maximum allowable fatigue load P for loading from a minimum load of 0.5*P to a maximum load of P. The parts are cast iron. The bolts are steel. No wa...

Question

Question

3. (35 points) For the joint below, determine the maximum allowable fatigue load P for loading from a minimum load of 0.5*P t

engineering Mechanical-Engineering

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

Dato DELTA Na 22-2 2. So Doto DELTA PO heel ron

Add a comment

Answer 2

Similar Homework Help Questions

[3]. (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates...

[3]. (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates from 0 to 7 kips The steel bolt specification is 5/8"-11 UNC, SAE grade 5 material with rolled threads. The clamped members are steel of length 1.25 in each (with a total length of 2.5 in). Plain wide washers are utilized at both ends of the bolt. [a]. Using the Goodman line, determine the factor of safety guarding against fatigue failure for the...
131- (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates...

131- (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates from 0 to 7 kips. The steel bolt specification is 5/8"-11 UNC, SAE grade 5 material with rolled threads. The clamped members are steel of length 1.25 in each (with a total length of 2.5 in). Plain wide washers are utilized at both ends of the bolt. [a]. Using the Goodman line, determine the factor of safety guarding against fatigue failure for the...
1. The section of the sealed joint shown in Fig. Q.1 is loaded by P 6.0 kip. The members have E-16 Mps, All bolts have been carefully preloaded to F. 25 kip a. If hardened-steel washers (American...

1. The section of the sealed joint shown in Fig. Q.1 is loaded by P 6.0 kip. The members have E-16 Mps, All bolts have been carefully preloaded to F. 25 kip a. If hardened-steel washers (American Standard, Narrow) are to be used under the head and nut, what length of bolts should be used (round up to the nearest 0.1 in)? (8 pts) b. Find kb, km (using 30° cone) and C. (24 pts) c Using the modifed Goodman...

The material is steel. hence the ultimate strength can be found.

the material is steel. hence the ultimate strength can be found. 131- (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates from 0 to 7 kips. The steel bolt specification is 5/8"-11 UNC, SAE grade 5 material with rolled threads. The clamped members are steel of length 1.25 in each (with a total length of 2.5 in). Plain wide washers are utilized at both ends of the bolt. [a]. Using the Goodman line,...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...

A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...

3. (35 points) For the joint below, determine the maximum allowable fatigue load P for loading from a minimum load of 0.5*P to a maximum load of P. The parts are cast iron. The bolts are steel. No wa...

Homework Answers

Add Answer to:
3. (35 points) For the joint below, determine the maximum allowable fatigue load P for loading from a minimum load of 0.5*P to a maximum load of P. The parts are cast iron. The bolts are steel. No wa...

Post as a guest

Earn Coins

[3]. (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates...

131- (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates...

1. The section of the sealed joint shown in Fig. Q.1 is loaded by P 6.0 kip. The members have E-16 Mps, All bolts have been carefully preloaded to F. 25 kip a. If hardened-steel washers (American...

The material is steel. hence the ultimate strength can be found.

A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...

3. (35 points) For the joint below, determine the maximum allowable fatigue load P for loading from a minimum load of 0.5*P to a maximum load of P. The parts are cast iron. The bolts are steel. No wa...

Homework Answers

Add Answer to: 3. (35 points) For the joint below, determine the maximum allowable fatigue load P for loading from a minimum load of 0.5*P to a maximum load of P. The parts are cast iron. The bolts are steel. No wa...

Post as a guest

Earn Coins

[3]. (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates...

131- (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates...

1. The section of the sealed joint shown in Fig. Q.1 is loaded by P 6.0 kip. The members have E-16 Mps, All bolts have been carefully preloaded to F. 25 kip a. If hardened-steel washers (American...

The material is steel. hence the ultimate strength can be found.

A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...

Add Answer to:
3. (35 points) For the joint below, determine the maximum allowable fatigue load P for loading from a minimum load of 0.5*P to a maximum load of P. The parts are cast iron. The bolts are steel. No wa...