here,
the input voltage , Vrms = 1 KV = 1000 V
power factor , phi = 30 degree
the input current is Irms
the output power , Po = 10000 hp = 7.457 * 10^6 W
the efficiency , e = 75 % = 75 /100 = Po /Pi
0.75 = Po /(Vrms * Irms * cos(phi))
0.75 = 7.457 * 10^6 /(1000 * Irms * cos(30))
solving for Irms
Irms = 1.15 * 10^4 A
the rms current is 1.15 * 10^4 A
An elevator uses a 10,000 hp motor. If the motor has a power factor of 30" and is 75% efficient, what is the amount of current necessary to operate the motor if the rms voltage is 1 kV? 8, mo...
Do number 53 please
The motor of a power saw is rated 72% efficient. If 1.8 hp are required to cut a particular piece of lumber, what is the current drawn from a 120 V supply? What is the efficiency of a dryer motor that delivers 0.81 hp when the input current and voltage4 are 4 a and 220 v, respectively? A stero system drawn 1.8 A at 120 V, The audio output power is 50 W. a. How much...
a 3 phase 440v induction motor has produced an output power of 75 hp and full load efficiency of 91% and power factor of 83%. A calculate nominal line current B if stator resistance per phase is .1omh what are copper losses at stator ? C if losses are 1.2 kw what is power delivered to rotor d determine i2r losses in rotor . E what is slip f synchronous speed is 1800 rpm what is the speed of motor
3) A four pole 75 HP 50 Hz induction motor with an efficiency of 93.4% has equivalent resistance and equivalent reactance per phase of 0.3000and 0.78 000OTHE blocked rotor voltage per phase is 175V. If the rotor is turning at 1425 rpm, determine synchronous speed, slip, rotor impedance, rotor current, total three phase apparent power crossing the air gap, its active and reactive components, rotor power factor, shaft speed, mechanical power developed and developed torque. (30 Points)
A 6 hp, 180 V shunt dc motor draws a full-load current of 30 A from the power supply. The motor has a field (shunt) resistance of 150 Ω. The armature resistance of the motor is 0.1 Ω. When the motor speed is 1800 rpm (this is not the full-load speed), the relationship between the induced voltage
1. An electric motor draws 2238 watts and 12 amperes when oper ating on a 240 volt 60 hertz source. Calculate: a. Power factor of motor b. Power input to motor c. Horespower output of the motor if it is 75% efficient. (Question no 4)
a. The figure below is a set of Synchronous Generator and Synchronous Motor. The ratings of the machines are as follows: Synchronous Generator:. 3ph, 1.0MVA, 2.3kV, 50Hz, 0.85 lagging power factor, X.=0.9 pu Synchronous Motor: 3ph, 0.5 MVA, 2.36V, 50Hz, 0.85 leading power factor, X.=0.8 pu Synchronous generator Synchronous motor The generator is equipped with a voltage regulator which maintains the terminal voltage at the rated value. The motor delivers 500 hp and it field current is adjusted to make...
(4) A 2.5 KW electrical motor with 0.9 power factor and 75% efficiency, is supplied with single core general purpose PVC cable passing through thermally insulated wall and 20m length. The heater is protected via BS3036 fuse with ambient temperature of 25°C. The ratings of BS3036 are shown in Table 1. The maximum permissible voltage drop is 6% of the rated voltage of 240 V. BS3036 Current ratings (A) 5, 15, 20, 30, 45,60 Table 1 Find: a) The design...
1. A 15 hp, 4 pole, 208 V, 60 Hz, Y-connected, three-phase squirrel cage induction motor has the following parameters in Ω/phase referred to the stator: R,-0.220, Xi = 0.430, X,-15.0, R2 0.130 and X2-0.430. Mechanical and core losses amount to 300 W and 200 W respectively for rated voltage. (a) The motor is fed with a 60 Hz, 208 V voltage. It runs with a slip of 4.5 %. Find the speed, shaft torque and power, efficiency and power...
32. A transformer is to be designed to increase the 30 kV-rms output of a generator to the transmission-line voltage of 345 kV-om. If the primary winding has 80 turns, how many turns must the secondary have? b. 70 c. 920 d. 9200 e 12 33. The primary winding of an electric train transformer has 400 turns and the Secondary has 50. If the input voltage is 120V(rms) what is the output voltage? a. 15 V (rms) b. 30 Vrms)...
15. (15 Points) For the following RMS voltage and current, answer the following questions: Voltage is given by v(t) = 12 cos(2t +30°) Current is i(t) = 4 cos (2t +10°) a. What is the Average power? b. What are the Phasors of each? c. What is the Complex Power? d. What is the Reactive Power? e. What is the Power Factor? BONUS 1. (5 Points) If an AC circuit has a current lagging the voltage, what type of circuit...