Question

6. In a high snowload area we have 60PSF of snowload on the following (3) modules. What is the maximum point load on one stan

max load point on each (one) standoff point for 3 solar pv modules ?

0 0
Add a comment Improve this question Transcribed image text
Answer #1

Tributary area of standoff point=2*(1.33+2.75/2)=5.4166 ft²

Snow load=60 psf

Point load=60*5.4166=325 lbs

This is the required answer

Add a comment
Know the answer?
Add Answer to:
max load point on each (one) standoff point for 3 solar pv modules ? 6. In a high snowload area we have 60PSF of snowload on the following (3) modules. What is the maximum point load on one stando...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • 1.) What is the fill factor of a solar cell having maximum power P(max) = 1.5...

    1.) What is the fill factor of a solar cell having maximum power P(max) = 1.5 W? The open circuit voltage and short circuit current of the cell are V(oc) = .6 V and J(sc) = 2.8 A, respectively. 2.) A solar cell with dimensions 12 cm x 12 cm is illuminated at standard test conditions. The cell has the following external parameters: V(oc) = .8 V, I(sc) = 3 A, V(MPP) = .75 V, I(MPP) = 2.5 A. Calculate...

  • 1. We have a PV module running at its maximum power point with Vm40 V and...

    1. We have a PV module running at its maximum power point with Vm40 V and Im 5 A. We wish to deliver power to a 12-volt battery to charge it. We want to use a DC-DC converter to accomplish this while extracting maximum power from the source (a) Propose a converter topology and specify the reason for that. (b) Solve for the duty cycle (D)

  • 2. Consider a single PV module supplying power to a resistance load. The hour-by-hour I-V curves...

    2. Consider a single PV module supplying power to a resistance load. The hour-by-hour I-V curves for the PV module are shown in Figure 1 along with the I-V curve for the resistance. For simplicity, consider each I-V curve to apply for one hour (e.g., the “8-am curve is from 7:30am to 8:30am. 1-sun means an absolutely sunny day. a. What is the load resistance? b. What is the total daily energy delivered to the load resistance (from 7:30am to...

  • Professor has 14 photovoltaic panels on his roof, and the effective PV area OF EACH PANEL...

    Professor has 14 photovoltaic panels on his roof, and the effective PV area OF EACH PANEL is 3ft x 5ft. At 12:20PM on October 12th, these panels were generating 2 kw of power. At that same time, the solar radiation measured by the weather station showed that the incoming solar radiation was 415 watts/m2 . 1. Determine the instantaneous efficiency of the system at this point. Note that you need to convert from square feet to square meters, and from...

  • PART II TRUE/FASE DIRECTIONS: Read each do not check the box PV array maximum collection potentia...

    PART II TRUE/FASE DIRECTIONS: Read each do not check the box PV array maximum collection potential. batteries to store surplus power for use at night or when periods of cloudy wea are especially appropriate for remote areas, such as national parks, cabins, and remote homes dan statement below Check thebox next to the statement if it is TRUE. If any part of the tem 1.Photovo(v) celis 2.In most locations in the U.S., a true north-facing orientation of a PV solar...

  • 3. Analyze this PV/battery system (ignore battery discharge rate and temperature constraints): 1. PV Module characteristics:...

    3. Analyze this PV/battery system (ignore battery discharge rate and temperature constraints): 1. PV Module characteristics: PR-100W, VR-20V, Voc 22V, IR-5A, Isc 6A 2. Battery characteristics: 6V, 100Ah (each) 3. Coulomb efficiency 90%; Maximum discharge 80% 4. Insolation: 6 kWh/m'day 5. Inverter efficiency: 80%; 6, Dirt, etc, efficiency: 90% (10% loss) 6 kW/m2-day 80% efficient AC 6V 100 Ah a. Find the watt-hours/day that would reach the loads (assume all PV current passes through the batteries): b.If the load requires...

  • ouUIC. ( HUU ULIC 3. ler one su 1000W/m2 A PV module with 36 cells in...

    ouUIC. ( HUU ULIC 3. ler one su 1000W/m2 A PV module with 36 cells in a series has photon current of 4A at 25°C under one sun.. Each cell characteristics are: I, is 0. 6A, R= 512 and Rs = 0.00512. a. If the mpp voltage across the load is 16.5V, find mpp current and the max power b. If one cell of the string is fully shaded, what would be output voltage across the load without bypass diode?...

  • help ASAP for my test Suppose we are investigating max./min. behavior of a function (1). We...

    help ASAP for my test Suppose we are investigating max./min. behavior of a function (1). We intend using the first derivative test, and have gleaned the following information in preparation for applying the test. Interval Test value Sign behavior of f'() of !") of (2) 7-20,-2) f'(-10) = -0.5 (-2,0) f'(-1) = -3 (0,2) SO = 2 + (2,00) f'(5) <0 Apply the first derivative using the information in the table to select the appropriate conclusion for each critical point....

  • [3 Marks] t sluex h à local maximum in Simulated Annealing? (d) Assume we have the following fitn...

    Qd (V) required help [3 Marks] t sluex h à local maximum in Simulated Annealing? (d) Assume we have the following fitness function x'-60 * + 900 * x +100 f(x) Using a binary representation we can represent x using five binary digits. i. Given the following four chromosomes give the values for x and fx). Chromosome Binary String 11100 P2 10111 00100 [2 Marks] nts, apply one point crossover. Use a crossover point of 1 (where [3 Marks] ii....

  • Please answer 2 and 1. Assignment No.6 10mH, C-20μF, an 1. A boost converter as the...

    Please answer 2 and 1. Assignment No.6 10mH, C-20μF, an 1. A boost converter as the following parameters: V,-20V, L Find the current spec of the inductor for continuous current mode (Max an Min current) -20 2. Switching frequency is 50 KHz and conduction duty cycle is 0.6 a. b. Calculate the output voltage and the ripple voltage An array has been formed with three modules in a string and two strings in parallel. The overall characteristic of the array...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT