The following truss is constructed of solid aluminum rods (2024-0) with a diameter of 0.5 inches and the applied load is 4000 pounds. Determine the loads and stresses in each of the members and the deflection of the center point.
All members are 14 inches long. All members are ½ inch diameter. All joints are pin joints.
Homework Answers
Add Answer to:
The following truss is constructed of solid aluminum rods (2024-0) with a diameter of 0.5 inches and the applied load is 4000 pounds. Determine the loads and stresses in each of the members and the de...
2. The following structure is constructed of 2" x 1/4" square steel tube, each member is 6 feet long, and the a...
2. The following structure is constructed of 2" x 1/4" square steel tube, each member is 6 feet long, and the applied load is 12kips. Model the structure as both a welded structure and as a truss structure and compare the results. At a minimum you should determine the loads and stresses in each of the members and the deflection of the center point for each model B F A D Applied Load
2. The following structure is constructed of...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and wall thickness as 0.4 inch and 0.05 inch, respectively. The Young's modulus and Poisson's ratio for aluminum are E= 10 x 10°psi, v=0.33, respectively. The applied load P is 60 Ib. Please answer = 60° B Ra all Cled URb The internal force for member AC is: -30 lb 34.6 lb 30 lb -34.6 lb Question 2 1 points Save Answer 1. The following...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
summatize the following info and break them into differeng key points. write them in yojr own...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
2. The following structure is constructed of 2" x 1/4" square steel tube, each member is 6 feet long, and the applied load is 12kips. Model the structure as both a welded structure and as a truss structure and compare the results. At a minimum you should determine the loads and stresses in each of the members and the deflection of the center point for each model B F A D Applied Load
2. The following structure is constructed of...
1. The following is a one-layer truss structure fabricated from aluminum tubing with outside diameter and wall thickness as 0.4 inch and 0.05 inch, respectively. The Young's modulus and Poisson's ratio for aluminum are E= 10 x 10°psi, v=0.33, respectively. The applied load P is 60 Ib. Please answer = 60° B Ra all Cled URb The internal force for member AC is: -30 lb 34.6 lb 30 lb -34.6 lb Question 2 1 points Save Answer 1. The following...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
Most questions answered within 3 hours.
-
This assignment will explore the impact of corporate decisions
on a local versus a global perspective....
asked 6 minutes ago -
Most political philosophers believe we have a duty to obey laws,
even if the laws in...
asked 41 minutes ago -
Which of the following are common negotiation outcome
mistakes?
a. Leave money on the table b....
asked 55 minutes ago -
Propose an efficient synthesis of 2-Bromo-5-nitrotoluene from
benzene. Hint: 3 steps. Consider directing effects of substituents....
asked 1 hour ago -
Convert the following quantities:
a) 0.819 atm to torr b) 512 mmHg to bar c) 11.2...
asked 1 hour ago -
C ++ Implement cat command
The purpose of this assignment is to provide practice using the...
asked 1 hour ago -
we
convert sugars into another form of stored potential energy. This
is called?
asked 2 hours ago -
The manufacturers of Oriental Spice Sauce are concerned that the
sodium levels in their product vary...
asked 2 hours ago -
PLEASE DON'T ANSWER IF YOU CAN'T ANSWER ALL OF THE QUESTIONS. I
DESPERATELY NEED HELP
Consider...
asked 2 hours ago -
DO NOT ANSWER IF YOU ARE UNSKILLED IN THIS AREA! TYPE OR WRITE
EACH ANSWER CLEARLY!!...
asked 2 hours ago -
how many moles of sodium are there in 3.41 moles of the
following compounds
NaCl
Na2SO4...
asked 2 hours ago -
1.1: Draw a position vs. time graph for a sprinter
running a 100 m dash. Label...
asked 2 hours ago