1.using Mesh analysis to find the Current, 2.then design it and find bias currents using PSPICE
f
1.using Mesh analysis to find the Current, 2.then design it and find bias currents using PSPICE 10Ω 50Ω 100 la is 4ia 100 i3 0.2vo Figure 6 10Ω 50Ω 100 la is 4ia 100 i3 0.2vo Figure 6
Using the mesh-current analysis, derive mesh current equations
for i1, i2, i3, i4,
i5, and i6. The values of dependent sources
should be replaced with the expressions of mesh currents in KVL
equations.
1. (20 points) Using the mesh-current analysis, derive mesh current equations for ii, i2, iz, 14, 15, and i6. The values of dependent sources should be replaced with the expressions of mesh currents in KVL equations. Do not need to simplify the equations and do not solve...
Use the mesh-current method to find the branch currents i1, i2,
and i3 in the circuit in figure (Figure 1) if v1 = 35 V and v3 = 81
V .Find the current i1.Find the current i2.Find the current i3.
Find currents I1 I2 I3 I4 I5
using loop (mesh) analysis, pleases use the directions indicated
for the currents. Please show work. Thanks in advance
2KC2 2mA 12V KC2 I, 2 1KS2 5 2K2 2KQ 4 1K(2
MULTISIM 4.36 a) Use the mesh-current method to find the branch PSPICE currents in, in, and i, in the circuit in Fig. P4.36. b) Repeat (a) if the polarity of the 140 V source is reversed. Figure P4.36 7512 150 12 Ic 80 V in 182000 140 V 1252 250 12 w w
Ignore PSpice Simulation
Design the MOSFET current mirror shown in Figure 2 to replicate a 1 mA reference current at the drain ofM2. Assume Vtn-1.2 V, L-100 μm, W-100 μm, kh-0.093 A/V2, and V,-100 1. Determine Ri such that IREF 1 mA is the current, Ipi, flowing into the drain of Mi. 2. Calculate lolREF, where lo = 1D2. 3. Simulate the circuit in Figure 2 in PSpice. Use the SEDRA LIB library for the MOSFET transistors and enter the...
mesh anal 5. (5 points) Find mesh currents 1, and I using mesh analysis. 1 ohm 1 ohm 2A( 12 1V upermessi M u 1+1.1, +1, 12-1=0 istia=2 (1-12=2
Use the mesh-current method to find the branch currents ia, ib,
and ic in the circuit in figure also find currents ia, ib, and ic
if the polarity of the 64 V source is reversed. The values of v1
and v2 are 64 V and 30 V, respectively.
4Ω 2Ω U1 1は10Ω 1Ω 3Ω
use mesh-current analysis to find the values of i1 and i2 in
figure p2.27. select i1 clockwise around the lefthand mesh, i2
clockwise around the righthand mesh and i3 clockwise around center
mesh.
ν + 8Ω w Figure P2.27
Using mesh current analysis,
what is the current I1 in the following circuit below.
10Ω 5Ω Ο 10 V 20 V 1Α
10Ω 5Ω Ο 10 V 20 V 1Α
Figure 3 (6) For the circuit in Figure 3, use Mesh Analysis to find the current through resistor R3 Recall let RI R2 10 k, R3=100 kQ, and V3.3 V.