Please all the questions. Give an estimate guess if u can't compute answer
Prob.1 (D)
IH, IG, GE, GH, and AB.
Prob.2 (D)
It is convenient when three or less than three member forces of a section are to be determined in a determinate truss.
Prob.3 (B) is the most near balue.
F= sum of forces or friction on the top and bottom surface of the central block = (0.2*50 + 0.2×100)*9.81 = 294.3 N
Please all the questions. Give an estimate guess if u can't compute answer Identify the zero-force members in the truss...
please short summarized answer 5minutes How many zero-force members are there in the truss shown? JB is rope. 3m 3m + Зm 3m А B с D 4m - 4 kN H G Select one: a. 3 b. 4 C. 2 d.5 How many zero-force members are there in the truss shown? M L K T N o P 2 m + A 2 m o O O o в с D E F G н 2 kN 2 kN...
Q1 a) List all the zero force members in the truss below Find Forces in AB, An and MN 2 m B C D E F G H I 2 KN 2 KN 5 KN 3 KN - 16 m, 8 @ 2 m
a) For the truss shown below identify all zero force members. (Circle) (10 Points) b) Determine the forces in members BE DE, and AB. (15 Points) y (4) 9 (4)-12(8), 9K 12 KN 4 m join 3m • 35.25 KM 0 3m 12 +35.25 + <DE TBy 35.25 АЧ BEST STU
For the Howe roof truss shown below: (a) List any members that have zero force [2 points] (b)Using the Method of joints, determine the force in member BD and state whether it is in tension or compression, if member AB is in compression with force of 1500lb. [10 points). Note the 3-4-5 triangles. 600 lb 600 lb 600 lb D 300 lb 300 lb 6 ft B 6 ft HI Αο C E G kot- -8 ft8ft-8 ft 8 ft
2nd pic is reference (Q3 Unit 1) (4) Assuming all members in the pin-pointed truss below (taken from Q3, Unit 1: Additional Examples sheet) have A = 2000 mm’and E = 200 kN/mm², determine the vertical displacement at E. 4 m 4 m 4 m * 3 m А E H it 80 KN 80 KN Ans: {vertical displacement 8E = - 1.43 mm (upwards)} 4 m 4 m 4 m 4 m + 3 m 80 KN 80 KN...
Please solve all the questions. 120 N Question No. 1: A 120-N force is applied to the control rod AB as shown. Knowing that the length of the rod is 0.6 m: 1. Determine the moment of the force about point B by resolving the force into: a. components along AB and in a direction perpendicular to AB. b. horizontal and vertical components. 2. Determine the horizontal force at A which creates the same moment. Question No. 2: Knowing that...
Determine the force in members CD and CM of the Baltimore bridge truss and state if the members are in tension or compression. Also, indicate all zero-force members. SK 2 m 0 H = SB C D E F G 2 kN 5 KN 3 KN 2 KN - 16 m, 8 @ 2 m 1. A light ray is incident from air on the surface of water (n=1.33) at an angle of 60° with the normal on the surface....
please answer #1 answers are in photo below questions. please solve 1. (20 pts.) The truss structure shown has 3 members: BD, CD and BC. The value of EA (where E-Young's modulus and A-cross-sectional area) for each of the members is 200 x 103 [kN]. (1) Determine the support reactions at B andCt (2) Determine the vertical displacement of the joint D, "D, (3) Determine the horizontal displacement of the joint D, uph. 0 30° 10 kN 2.13mm 2. (20...
Please answer all parts of the questions and please try making them clear and easy to understand. CONCEPTUAL QUESTIONS: (Total Points 10, 1 points each question) 1- A plate is supported by a bal-and-socket joint at A, a roller joint at B, and a cable at C. How many unknown support reactions are there in this problem? 300 N 400 N i m A) Four forces and two moments B) Six forces C) Five forces D) Four forces and one...
Question I.5 Figure 1.5 shows a frame with loads at A and D. Select the closest value for the magnitude of the total reaction at B. Assume the weight of the frame is zero. 40 kN VE 96.2 kN (a) (Ь -40 kN 5 m (c) -87.5 kN 30 kN (d) 57 kN 4m ao 1 m (e) 50 kN Figure L.5 Low mass frame Question I.6 In the shear and bending moment equations for beams, which of the following...