(30 pts) Consider the following sampling system where the input is x(t) = sin 2nt + cos 3nt r(t) Cp (t) (a) (10 pts) Fi...
Problem 1: (3 +2+3+2 10, sampling) Consider the continuous-time signal x(t) = 3 + cos(10?1+ 5) + sin(15?), t E R (a) Find the Fourier transform X-Fr. Hint: (F ejuot) (w) 2??(w-wo) (b) What is the Nyquist Frequency wn in radians/s of x? (c) Write an expression for the Fourier transform of the ideal sampling of x with sam- pling period T, = 2n/Cav.), i.e., ?00_ox(AZ)6(t-kZ) Hint: (F eiru>tz(t) (w) - X(w - rus) and recall Poisson's identity, CO eyru'st,...
Problem 4.(30 pts) Given the analog signal x(t) cos(2 cos(3t)+2 sin(4mt) A.(10 pts) Find the Nyquist frequency (sampling frequency) which guarantees That x() can be recovered from it's sampled version xIn] with no aliasing. B.(10 pts) If the sampling period of Ts 0.4 see is used identify all discrete frequencies Of the signal x(t), also indicate if this sampling period is adequate to recover x(t) from xn] C.(10 pts) Suppose signal x(t) is modulated by signal e(t) = cos(2000mt) what...
Signal system 8. Consider the periodic signal x(t) = cos(2nt) + cos(2nt) I. a. Find the Fourier series coefficients for this signal. (4 points). b. If this signal passes through a LTI system with the impulse response h(t)=e* u(t), particularly, would the output signal also be a periodic signal ? If so, what would be the Fourier coefficients of the output signal ? (4 points). c. Give the mathematical expression for the output signal y(t). (2 points).
Please answer the following fully with detailed justification/explanation. Thank you. Consider the signal e(t) (60m sin (50t) (a) Determine Xc(jw), the Fourier transform of e(t). Plot (and label) Xe(ju) b) What is the Nyquist rate for re(t)? (c) Consider processing the signal re(t) using the system shown below: Conversion to a Ideal to an e(t) y(t) impulse train Filter H-(ju) The sampling rate for this system is f DT filter is shown below 150 Hz. The frequency response of the...
10. Find the Fourier transform of a continuous-time signal x(t) = 10e Su(t). Plot the magnitude spectrum and the phase spectrum. If the signal is going to be sampled, what should be the minimum sampling frequency so that the aliasing error is less than 0.1 % of the maximum original magnitude at half the sampling frequency. 11. A signal x(t) = 5cos(2nt + 1/6) is sampled at every 0.2 seconds. Find the sequence obtained over the interval 0 st 3...
3. (a) Consider the signal xc(t)-sin(2π(40)t). How fast must xe(t) be sanpled to avoid aliasing? Determine the Nyquist rate (the frequency which the sampling rate fs must exceed) for ae(t) (b) Consider processing the signal xe(t) (from part (a)) using the system shown below: Conversion to a sequence Conversion to an impulse train Ideal Reconstruction Filter Hr(ju) p (t) ур y(t) The sampling period for this system is T-1/50 seconds. The DT system H(ei2) is an ideal lowpass filter with...
Consider the following DT periodic signal: in X(t) = sin 2πη) 10 + cos 30) a) What is the fundamental period? b) What are the exponential Fourier series coefficients? c) Sketch magnitude and phase spectral plots.
please show steps, focus on part b more 1. (23 points) Sampling and Aliasing. (a) Find the Nyquist sampling rate wn for the given x(t). (Recall that the sampling frequency has to be twice larger than the bandwidth of the signal to recover the signal without loss of information.) i. (5 pts) X(t) = sinc(5000) * cos(7t). ii. (5 pts) r(t) = sin(101) cos(106) iii. (5 pts) (t) = sinc(50000) + cos(56) (b) (8 pts) Let r(t) = sinc(t/h), y(t)...
Consider the continuous time signal: 2. , π (sin (2t) (Sin (8t) A discrete time signal x[n] -xs(t) -x(nTs) is created by sampling x() with sampling interval, 2it 60 a) Plot the Fourier Transform of the sampled signal, i.e. Xs (jo). b) Plot the DTFT of the sampled signal, ie, X(eja) o) Repeat (a) with 7, 2π d) Repeat (b) with , 18 Consider the continuous time signal: 2. , π (sin (2t) (Sin (8t) A discrete time signal x[n]...
2. Consider the signal f(t) = 20 cos(5t) + cos(9t) sin(5t) - 7 (a) What is the highest angular frequency present in this signal? What is the highest numerical frequency present in this signal? (b) What is the Nyquist frequency? rate for this signal? Did you use the angular or the numerical (c) If you sample this signal with sampling period T, which values of T may you choose to be in accordance with the Nyquist rate? Choose and fix...