6. A flat plate is made of steel with mass density p= 7850 kg/m3. The thickness of the plate is 10 mm. Calculate the re...
9. A truss and a steel cable are supporting a mass of m = 20 kg as shown. A cable is supported by a frictionless pulley at point B for L = 500 m, d = 200 m, and h = 300 m. (a) (2 marks) Draw a free-body diagram and show all forces that act on this structure (b) (1 mark) Find the magnitude of the tension force in the steel cable, (c) (3 marks) Find the x and...
A P=2-kN tensile load is applied to a test coupon made from
1.6-mm thick flat steel plate (E = 220 GPa, v =
0.30). Assuming a=45 mm and b=13 mm,
(a) Determine the resulting change in the 45-mm gage length.
(b) Determine the resulting change in the 13-mm width.
(c) Determine the resulting change in the 1.6-mm thickness.
(d) Determine the resulting change in the cross-sectional
area.
The uniaxial state of stress in given as ________ (MPa)
A P-2-kN tensile...
A steel (density 7.86 x 103 kg/m3) wire of length 1.20 m and diameter 0.644 mm is subjected to a tension of 34.5 N. At one end of the wire is an oscillator harmonically oscillating one end of the wire at a frequency of 60 Hz, the other end of the wire runs over a pulley to a hanging mass that supplies the tension.What is the wavelength of the waves produced by the oscillator?
X Incorrect. The boundary-layer thickness, 5, on a smooth flat plate in an incompressible flow without pressure gradients depends on the freestream speed, U, the fluid density, p, the fluid viscosity, u, and the distance from the leading edge of the plate, x. (a) Express these variables in dimensionless form and (b) calculate dimensionless parameter (proportional to x) with x 0.150 m, p 385 kg/m3, U 0.147 m/s, u 0.2 x 104 N-s/m2. Click here to enter or edit your...
Consider air flows with velocity of U?=U= 10 m/s over a
semi-finite smooth flat plate with L=97 cm long. Calculate the
followings by assuming ? = 1.568 x 10-5 m2/s and ?=1.177
kg/m3.
Figure 1 : Boundary layer over a flat plate
Consider air flows with velocity of U?=U=10 m/s over a
semi-finite smooth flat plate with L=97 cm long. Calculate the
followings by assuming ? = 1.568 x 10-5 m2/s and ?=1.177
kg/m3.
b) Under some flow and boundary...
4- A steel strip of thickness 6-12 mm is annealed by passing it through a large fumace whose walls are maintained at a temperature Tw corresponding to that of combustion gases flowing through the fumace (Iw Tp). The stip, whose density, spcific thermal conductivity, and emissivity are 79 kg/m3, cp -640 J/kg K, k 30 W/m K and 0.7, respectively, is to be heated from 300°C to 600°C Furnace walls, Combustion gases For a unifom convection coefficient of h-100 W/m2...
Question 6: Moment of inertia of an algebraic shape A plate of uniform areal density p= 4 kg/m2 is bounded by the four curves: y= -x2 – 2x – 4 m y=-23c2 + 4x + 19 m x = -2 m x = -1 m, where x and y are in meters. Point P has coordinates Pc = -1 m and Py = –3 m. What is the moment of inertia Ip of the plate about point P? Ip =...
The high E-string of a steel string guitar is about L = 0.7m
long. It has a mass per unit length of p = 5.3 *10^-4 kg/m. Find
the tension T required to properly tune the string, given that a
high E has a frequency of f = 1318.51 hertz
(a) The high E-string of a steel string guitar is about L 0.7 m long. It has a mass per unit length of ρ= 5.3 x 10-4 kg/m. Find the...
2. (1O pts) A flat bar of an annealed metal, whose strain-hardening behavior is expressed by σ 800 (10) es N m2, originally 25 mm in thickness. By a series of tw o consecutive reductions the initial thickness is reduced to 20 and 15 mm respectively under plane strain condition (the width of the bar , wis not changed). What is the new yield strength of the material? What is the temperature rise in this adiabatic deformation process? The pertinent...
Problem 1 An incompressible, viscous fluid with density, p, flows past a solid flat plate which has a width, b, into the page. The flow initially has a uniform velocity U before contacting the plate. The velocity profile at location x is estimated to have a parabolic shape, u-u[(Y)-(,)21"for ysiand u-vfor y 20 where isthe boundary layer thickness. (a) Determine the upstream height from the plate, h, of a streamline which has a height, 6, at the downstream location, x....