lumped element matching network and single stub 2. A transmission line of characteristic impedance Zo 50Q is termina...
6. Design two single-stub matching networks as shown below. Transform the load impedance Z (60 j45) Ω to match an input impedance of Z,-(75+j90)Ω. Assume that both the stub and the transmission line shown below have a characteristic impedance of Zo-50 Ω. Zot I ZoL.l ZL lm in Open or -) : short circuit , open or short circuit 6. Design two single-stub matching networks as shown below. Transform the load impedance Z (60 j45) Ω to match an input...
8.16 Using matching network shown below, find the stub length ls the characteristic impedance Zou and the transmission line length 11 such that the ZL = (80-j40) Ω load impedance is matched to a 50 Ω source. Assume that the characteristic impedance of the stubs Zos = 50 Ω. Zas ls Zin Open or short circuit 8.16 Using matching network shown below, find the stub length ls the characteristic impedance Zou and the transmission line length 11 such that the...
5. Double Stub Matching Network Design a double shunt open-circuit stub matching network to match a load impedance Z, = 80-j60 Ω to a 50 Ω air-filled line operating at frequency f = 1 GHz、The distance between the stubs is,-/8. Sketch the resultant network and specify the line lengths in millimeters. 5. Double Stub Matching Network Design a double shunt open-circuit stub matching network to match a load impedance Z, = 80-j60 Ω to a 50 Ω air-filled line operating...
Design two parallel open single-stub matching network that match a load 60-j45 Ω to a source with an internal impedance 75-j90 Ω. Assume that both stub and the transmission line have a characteristic impedance of 75 Ω.
answer number 3 and 4 Problem 7. Transmission Lines The figure below shows a transmission line with a characteristic impedance Z,-50 Ω, connected to a single frequency generator with an internal impedance R,-50 C (not shown), and terminated in a purely resistive load RL 50 2. At the frequency of the generator, the wavelength of the transmission line is λ = 2 m. At a distance dl-1.25 m away from the load, a shorted stub is connected via a tee....
A lassless transmission line with characteristic impedance Zo - 50 R and length l = 0.42 is terminated into a load Z2 = 100+j401 (a) At what distance from the load is the input impedance real? (4 points) (b) If a quarter-wave transformer is to be used to match the load to the transmission line, what will be its characteristic impedance ? (4 points)
Stub Matching Netowrks Use a SMith chart to design an open-circuit shunt-stub transmision line single-stub matching network to transform a 50ohm termination to a load impedance of ZL=10+j30ohm with system impedance of 50 ohm. sketch the network, indicate the line lenghts on the sketch, and specify the stub and line lenghts in wavelenghts.
A transmission line has an unknown characteristic impedance of Zo. The length L of the transmission line is also unknown. When the transmission line is short circuited (Zi - 0) at one end, the measured input impedance at the other end is Zv Zsc. When the transmission line is open circuited (Zi- oo) at one end, the measured input impedance at the other end is ZiNZoc Find the characteristic impedance Zo of the transmission line.
Q1. (20pts) Consider a lossless transmission line with characteristic impedance Zo=50 Q is used to connect a sinusoidal source with internal resistance Rs=50 2, and 10 Volts peak value to feed a load of ZL=300 Q. At an operating signal wavelength of do, the length of the transmission line is L=2.25o. Determine the followings: a) Standing wave ratio on the line b) Average power delivered to the load in dBm. c) The voltage and current phasor expressions on the transmission...
Question 4 (a) The input impedance of a lossless air-core transmission line with characteristic impedance Ro. phase constant B and length I terminated in an impedance Z, is given by R,+Z, tan( i. Determine the length of an open circuit 50Ω line required to create a 0.1 nH inductor at a frequency of 10 GHz. (6 marks) ii. Determine the input impedance of the line in part () if the open circuit is changed to a short circuit. (3 marks)...