The device is used to measure a change in temperature. Bars AB and CD are made...
The device is used to retur a change in temperature Bars AB and CD made of A-s steel and 2014- TO aluminum alloy respectively. When the temperature is at 35 C, ACBs in the po Figure 1) Part A Determine the vertical power of the whether to Express your answer to the significant figures and include the propriate units. Ente positive value the displacement is upward and negative or if the displacement is downward. Figure WA Value Units Suterit <...
The switch shown is designed to close as the temperature rises causing AB and CD to expand and making point E come in contact with point F. Arm AB is made of steel with a CTE of ast12x106 /oC, and arm CD is made of aluminum with a CTE of aal = 24x10-6 /°C, At 20 °C, arm BDE is vertical as shown. Determine the required gap, s, (at 20 °C) if the switch is to close at 110 C,...
The 5k load is supported by the assembly shown. Assume beams AB and CD are rigid members and are horizontal before the load is applied. Members BE and CF are made of 2014-T6 aluminum (E=10.6*103 ksi). Determine the vertical displacement of the load if BE has dimensions of 0.3" x 0.2” and CF has dimensions of 0.15” x 0.25”. (15 pts) 2 ft 8 ft 2 ft2 D с A E lo 1.5 ft B 6 ft 6 ft 5...
blem 5 (25 points): Consider the system of bars shown below. Bars AB, CD, and EF are connected d link BED. Determine the horizontal displacement of point F B by a rigid . Bar AB has a cross-sectional area of 0.012 m2, a Young's modulus of 200 GPa, and a length of 0.34 m. . Bar CD has a cross-sectional area of 0.010 m2, a Young's modulus of 200 GPa, and a length of 034 m . Bar EF has...
The AB tube made of a magnesium alloy AM1004-T61 is covered
with a rigid plate E. The spacing between E and the C-end of the CD
solid circular bar, made of a 6061-T6 aluminum alloy, is 0.2mm when
It has a temperature of 30 Centigrade. Deteremina:
a) Are the forces to which the AM1004-T61-76 tube is subjected
if the temperature of the magnesium tube rises to 130 C?
b) What is the deformation of each bar?
c) Do any of...
А 6061-T6 aluminum tube is used as a sleeve for a steel post Tool L2 as shown. When not loaded, and at a temperature of 60 F, both the tube and post have a length of 24 in. The system is subjected to a load P and the temperature is increased to 115 F Assume that both the tube and post are rigidly connected to the rigid cap. Determine the load P required to restrict the system's length change to...
can you please do problems 4 and 5
Problem 4 The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm diameter 304 stainless steel rod EF and a rigid bar G. If the horizontal displacement of end F of rod EF is 0.45 mm, determine the magnitude of P. 300 mm 450 mm IP Problem5 The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 14 mm2...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...