Concentrations of dissolved solids in water are often reported in parts per million (ppm) or parts...

Question

Question

Answer 1

Answer #1

en appb = 1 Mg/L : 365pp6 = 365 Mg / pb molar mass=207 g/mol 1 mole 2079 1 mole = 4o mmole (millimole = mmoles- 1 gram = 100

Answer 2

Similar Homework Help Questions

Concentrations of dissolved solids in water are often reported in parts per million (ppm) or parts...

Concentrations of dissolved solids in water are often reported in parts per million (ppm) or parts per billion (ppb). One part per billion of a solute is equivalent to 1 ug (microgram) of that solute dissolved in 1 litre of water (i.e., 1 ppb = 1 ug/L). The toxic water crisis in Flint, Michigan in 2015 yielded test results of up to 1051 ppb of lead dissolved in tapwater. (The maximum allowable concentration set by Health Canada is 5 ppb)....
Part B: Parts Per Units Parts per million (ppm) and parts per billion (ppb) are common...

Part B: Parts Per Units Parts per million (ppm) and parts per billion (ppb) are common units for environmen- tal samples. The calculations are very similar to the percentage units. (which are es- sentially parts per hundred units). The mass units must be the same for the numerator and denominator, so these units cancel during the calculations. units; show all Please answer the following questions involving the parts per of your calculations. 7. A sample of river water was analyzed,...
Flint, Michigan faces a serious water contamination crisis with high levels of lead (Pb) found in...

Flint, Michigan faces a serious water contamination crisis with high levels of lead (Pb) found in the water. The EPA has a limit of 0.015 mg/L. Express this concentration in units of ppb. Assume the water has a density of 1 g/mL.

In clinical applications, the unit parts per million (ppm) is used to express very small concentrations...

In clinical applications, the unit parts per million (ppm) is used to express very small concentrations of solute, where ppm is equivalent to 1 mg of solute per 1 L of solution. Calculate the concentration in parts per million for cach of the solutions. There is 29 ug of calcium in a total volume of 61 mL. concentration of calcium: ppm There is 0.57 mg of caffeine in a total volume of 109 ml. concentration of caffeine: ppm There is...
The drinking water in Saplingville was found to contain 12 ppb (parts per billion) of lead....

The drinking water in Saplingville was found to contain 12 ppb (parts per billion) of lead. What is the concentration of lead in molarity?
3. Concentrations in solids and solution. You send a 10-g sample of rice to the lab...

3. Concentrations in solids and solution. You send a 10-g sample of rice to the lab for the determination of the total arsenic content. The analyst dissolves 1.0 g of the rice in 5.0 mL of concentrated acid and then dilutes the solution to a final volume of 25.0 mL. When analyzed by ICP-MS, the solution concentration is found to be 35 µg L-1. What is the concentration of arsenic in the rice (in µg kg-1)? ___________ ppb Hint: Follow...

Parts per million (ppm) strengths 31 If drinking water contains 0.7 ppm of fluoride, how much...

Parts per million (ppm) strengths 31 If drinking water contains 0.7 ppm of fluoride, how much fluoride (in milligrams) would be present in 1 litre of water?
Hard water normally contains mineral ions, such as Ca2+ and Mg2+ ions, from minerals that dissolved...

Hard water normally contains mineral ions, such as Ca2+ and Mg2+ ions, from minerals that dissolved in the ground water. For water of low hardness, the concentration of Ca2+ ions is usually expressed as ppm CaCO3 in the water sample. Parts per million (ppm) is defined as one part of solute mass per 1,000,000 parts of solution mass, as shown in the following equation. Please note, the unit of denominator and numerator needs to be the same. Since ppm expresses...
For the preparation and standardization of NaOH with KHP im supposed to boil water for 1hr and 30 min to remove CO2

For the preparation and standardization of NaOH with KHP im supposed to boil water for 1hr and 30 min to remove CO2....the problem is that if I don't boil it for that long and (30 min) b/c of not enough time but I put the water I boiled for 1/2 hr aproximately into a NaOH bottle with a CO2 absorber and stored it there for a few days. I would assume that I would have to boil the water again...but...