Please show me how to obtain the final answer:
Please show me how to obtain the final answer: 4.4 A muscle .iennalon omplex is loaded...
The answer is below. Please show me step by step how to obtain
the answer.
The length change of a muscle, with respect to the length to in the relaxed state, can be written as δ = 1-10. (a) Give an expression for the force F in the activated muscle as a 41 (b) What is the magnitude of the force F when δ 0? 0 ( 운
Please show me how to do b)
The answer is ≈ 220N
reality the force length equati only valid in a very limited range of extension ratios. The force that a sar- comere (and thus a skeletal muscle) can exert has a maximum, as depicted in the figure below. Sarcomere lengths at several interesting points in the graph are depicted by Li, with i1,....5. L2 100 Maximumm L3 ension 60 (96) L5 40 し4 20 0) 0.5 1.0 1.5 2.0...
The answer is listed below. Please show me how to obtain the
answer.
3.3 A person is lying on a board, which is supported at both ends. A vertical reaction force VA is acting on the board at point A and passes through the origin of the coordinate system. A vertical reaction force VB is acting at the point located in iB -le I is known that the weight of the person is F and the weight of the board...
Can you please show me a detailed solution to this problem.?
A long steel (SAE 1018HR) plate is welded on both ends as shown in the following figure. The plate thickness is 10mm. The dimensions shown blow are b = 50mm, d = 25mm, c = 200mm, h = 5mm. A concentrated force F is applied at the center. The electrode material is E7010. A factor of safety is assumed to be 2.5 for both plate and welding. Find the...
The answer is -66.7% please
show me how to get to this answer. Please be detailed and show step
by step.
5. As shown on the right, a uniform disk with M = 1.000 kg and D = 50.00 cm is initially rotating at 10.00 radians/s when a non-rotating thin ring of the same mass and radius is gently dropped vertically onto it. Their centers of mass and axes of rotation align after the perfectly inelastic collision. What percentage of...
please help me with question 4. Thank you
Instructions: Showing Steps (or mathematics involved) is not necessary until explicitly stated in the ques- tion. Just writing the final answer is fine. • However, if you decide to show steps, then you will get partial points for the steps even if the final answer is wrong. • Standard integrals can be written directly without showing the integration. • All final answers must be in SI units and the units must be...
Can someone show e how to solve this please
2. Given the beam in the figure, the concentrated load F is 600 lb, the distributed load w is 50 lb/in, a is 10 in., bis 15 in., and I is 20 in. The beam is made of steel with E equal to 30 X 10 psi. The beam is rectangular with dimensions h = 5 in and t = 2 in. Determine the following: a. The reactions and the shear...
I
really hope you can give me a complete answer and explain it ,
please don‘t Answer if you cannot
I will definitely rate a good answer. thanks
Show that the 3D force field is a conservative field. Find the work done against the force when moving from Write down (i) an expression for the gradient of a 3D scalar field Ф(x, y, z) and (ii) the pseudo-determinant expression for the curl of a vector field v. Then show that...
Can someone help me please and clearly show step by step how to get the answer. I can't figure it out. *For each of the following reactions, 16.0 g of each reactant is present initially. CS2(g)+3O2(g)→CO2(g)+2SO2(g) -Calculate the grams of product in parentheses that would be produced. (CO2)
help, please.
Instructions: Enclose final answer(s) in a box. Show starting equations and enough steps of your work for me to follow (and give partial credit when possible). 12 Score: points 1. A beam has a length of 10.00 meters and a mass of 133 kg. It is to be balanced on a fulcrum 2.65 meters from the right edge. A block of mass 135 kg is placed at the extreme right end of beam. a. How far from the...