Please Help!!!!!! QUESTION 13 Given the density of air near the Earth's surface as 1.1839 kg/m3,...
Please Help!!!!! QUESTION 14 A 21 kg block of iron is suspended from a spring with spring constant 118 Nm. tis lowered into a vat of oil density 0.92 g/cm3) and fully submerged. Given that the density of iron is 7.87 g/cm3, how far (in m) is the spring stretched from its rest length? QUESTION 15 A block of yellow pine has a density of 426 kg/m3 and floats in a large tub filled with water (density 1,000 kg/m3) A...
A 1.00-kg beaker containing 2.00 kg of oil (density = 916 kg/m3) rests on a scale. A 1.50-kg block of iron is suspended from a spring scale and is completely submerged in the oil (see figure below). Find the equilibrium readings of both scales.
Please Help!!! QUESTION 15 A block of yellow pine has a density of 421 kg/m3 and floats in a large tub filled with water (density 1,000 kg/m3) A 373 kg block of aluminum rests on top of the wood.if the aluminum remains above the surface of the water, what is the minimum volume (n m3) of the block of yellow pine?
A U-tube contains liquid of unknown density. An oil of density 770 kg/m³ is poured into one arm of the tube until the oil column is 13.5 cm high. The oil-air interface is then 4.5 cm above the liquid level in the other arm of the U-tube. Find the density of the liquid. A raft is made of 11 logs lashed together. Each is 38.0 cm in diameter and has a length of 7.00 m. How many people (whole number)...
13. To measure moderately low pressures oil with a density of8.0 x 102 kg/m' is used in place of mercury in a barometer. A change in the oil column of 1.0 mm indicates a change in pressure of about: A) 1.2 x 104 Pa B) 0.078 Pa C) 0.85 Pa D) 7.8 Pa E) 8.3 Pa 14. The principle of fluid pressure which is used in hydraulic brakes or lifts is that: A) pressure is the same at all levels...
How to solve question 44 s the anoint P, where FIGURE P13.40 gauge pressure of the the needle meets the wider chamber of the syringe? A 6 General Problems 41 Il As discussed in Section 13.4, a person' of titanium is 4.5 g/cm3. 125 g of titanium iss weight of the sph l The shaped into a cube. What is the length of each edge? You need to d s percentage of body fat suspend it R0 can be estimated...
Please help me answer this question it 1 question from A to J. PHY HW. • Moments of inertia formulas are provided on the last page of this document • Show all of your work when solving equations. It is not sufficient to merely have a correct numerical answer. You need to have used legitimate equations and algebra. You also need to have correctly used the data. • Units must be specified for any isolated number, not just your final...
Please help answer all of question 6, thanks! Rotational Dynamics Assignment (200 Points) • Due Friday, July 31 at 5:00 pm Equations are in a separate document entitled “Equations for Rotational Dynamics Assignment” • Moments of inertia formulas are provided on the last page of this document • Show all of your work when solving equations. It is not sufficient to merely have a correct numerical answer. You need to have used legitimate equations and algebra. You also need to...
* This is all the information given QUESTION 1 (iii,iv) PLEASE!!!: Examine the car performance when the angle of both the front and rear wings is set to θ = 10◦. In all the analysis that follows ignore frictional losses other than drag. Determine: (iii) What is the maximum speed the vehicle can safely corner a bend with R = 30 m (ans. 108Km/hr). What is the power required at this speed? (ans. 27.8KW) (iv) What is the maximum speed...
* This is all the information given QUESTION 1 (iii,iv) PLEASE!!!: Examine the car performance when the angle of both the front and rear wings is set to θ = 10◦. In all the analysis that follows ignore frictional losses other than drag. Determine: (iii) What is the maximum speed the vehicle can safely corner a bend with R = 30 m (ans. 108Km/hr). What is the power required at this speed? (ans. 27.8KW) (iv) What is the maximum speed...