From the figure, the vernier coincidence is at 7.5 and thus the vernier scale division= 2*7.5=15
And the main scale reading is 17mm.
And LC= 0.05
Thus, the diameter = main scale reading+(vernier coincidence×LC) - ZE = 17 + (15×0.05) - 0 mm = 17.75 mm
record the main scale reading and vernier coincidence. calculate the diameter using formula Diameter= main scale...
record the main scale reading and vernier coincidence. calculate the diameter using formula Diameter= main scale reading+(vernier coincidencex LC) - ZE. LC= 0.05 ZE= 0 60 70 Imam o 0.05mm
record the main scale reading and vernier coincidence. calculate the diameter using formula Diameter= main scale reading+(vernier coincidencex LC) - ZE. LC= 0.05 ZE= 0 Խանասնահատականանասնականանամական 0 1 2 3 4 5
record the main scale reading and vernier coincidence. calculate the diameter using formula Diameter= main scale reading+(vernier coincidencex LC) - ZE. LC= 0.05 ZE= 0 հանունակականանաանանանահամանունուն ՝ 5 6 7 á õ օ.05mm .
Record the smallest interval displayed on the main scale as S. Count the number of division if the Vernier scale and Record as N. Calculate the least count of the device using the formula LC= S/N. 110 150mm 05mm
Vernier Vernier scale reading question in Physics class Hydrogen Balmer Serie CanYou PleaseHelp Me Wi Exercise B Lateral Band Walk 己 -S G> (> www.phys.utk.edu labs Hydrogen%20Balm r%20Senes%20and%20Rydberg%20Constant%20Prelab pdf -) 0 2. What is the reading of the Vernier scale shown below? VER I 30 20 10 IO 30 20 :19 PM 0 Type here to search
please calculate the based on pink sheet Data Analysis Using the scale position reading for the hydrogen spectrum and the equation generated from your calibration curve, calculate the wavelengths (in A) for each of the four lines in the hydrogen spectrum. Compare these calculated values with the reported values. Look up the four lines that are visible in the atomic spectrum of hydrogen (Be sure to provide a reference or URL). Convert the wavelengths in Å to nm and m,...
DIRECTIONS: Work the problem. You must show all work to receive credit, and you must return this sheet. Be sure to explain carefully your answers and show your work in a neat and organized manner. The problem is worth 20 points. A right angle triangular prism has a cross section shown in the figure and is made from a material whose density is 5.75 g/cm². The height of the prism is the same as its side L, whose length is...
A 2.00” diameter billet will be reduced in diameter to 1.00” using direct extrusion as shown below. The strength coefficient and strain hardening exponent of the material are K = 60,000 lb/in2 and n = 0.18. The coefficients for Johnson’s strain formula are a = 0.8 and b = 1.5. The ram force available on the extrusion press is 1.75 X 10^6 lb. Calculate the maximum length (Lmax) of billet that can be extruded. Container Ram Final work shape F...
Find the densities with error: Calculate the volumes, V, and V2, and densities, ρ, and f, required in the tables below. You need to determine the correct uncertainty, e.g. AL, for each instrument. Check with your instructor. Also, read the Introduction in this experimental procedure. Cylinder 1 (the reddish-orange-colored one)5 Mass: (The uncertainty in the mass is ½ the smallest division on the scale; see the text.) et Ruler Vernier Caliper Micrometer Measurement 5.05측 Length, L (cm) Uncertainty in L,...
Open with Google Docs ▼ Question 3 Calculate the flow rate of water in a pipe of 30 cm diameter placed in an inclined position where a venturi meter is inserted, having a throat diameter of 15 cm. The difference of pressure between the main and throat is measured by a liquid of s.g. 0.6 in an inverted U-tube which gives a reading of 30 cm. The loss of head between the main and throat is 0.2 times the kinetic...