The drill is jammed in the wall and is subjected to the torque and force as...
The drill is jammed in the wall and is subjected to the torque and force as the below picture
a) Determine the axial force (P), transverse shear (V), torque (T), and bending moment (M) on cross-section a-a.
b) Calculate max stresses on the cross-section a-a due to loads P, V, T and M EACH.
c) Combine all stress components at point B that is on the a-a section from part b) and draw a stress element at B. Determine the principal stresses at point B.
Homework Answers
Add Answer to:
The drill is jammed in the wall and is subjected to the torque and force as...
The circular beam is subjected to a torque and vertical shear force. At which point on the cross ...
The circular beam is subjected to a torque and vertical shear force. At which point on the cross sections is there a non-zero stress due to both loads, and the stresses due to both Torsion and Shear act in opposite directions?
The JT100 horizontal directional drilling machine applies 220 hp and rotates drill pipe at 100 rp...
The JT100 horizontal directional drilling machine applies 220 hp and rotates drill pipe at 100 rpm. During the drilling process, a drill pipe is subjected to the following axial and bending loads 30.0 Axial load, P, of 100 kips 0.70 ft-kips bending load, M, in the y-z plane at 30 degrees from the vertical axis The drill pipe, which is made of AISI 4130 steel, has the following dimensions and material properties (Ref. MIL-HDBK-5J, Table 2.3.1.0(c1)) » Length, L 177-in...
M15.3 Principal stresses in a rectangular tube scenes The rectangular tube is subjected to a transverse shear force of...
M15.3 Principal stresses in a rectangular tube scenes The rectangular tube is subjected to a transverse shear force of V = 230 kN and a bending moment of M = 530 kN-m, each acting in the directions shown. Determine the bending stress, the transverse shear stress magnitude, the principal stresses, and the maximum shear stress magnitude acting at location H. У Он (MPa) H 550 mm TH (MPa) 65 mm Op1 (MPa) X Op2 (MPa) 12 mm ITmax (MPa) wall...
The inverted tee shape is subjected to a transverse shear force of V = 90 kN and a bending moment of M = 35 kN-m
M15.2 Principal stresses in a tee beam The inverted tee shape is subjected to a transverse shear force of V = 90 kN and a bending moment of M = 35 kN-m, each acting in the directions shown. Determine the bending stress, the transverse shear stress magnitude, the principal stresses, and the maximum shear stress acting at location H.
A pressurized pipe with an outside diameter of 13.1 in. and a wall thickness of 0.375...
A pressurized pipe with an outside diameter of 13.1 in. and a wall thickness of 0.375 in. is subjected to an axial force of P = 34000 lb and a torque of T = 9400 lb-ft, as shown. If the internal pressure in the pipe is 260 psi, determine the principal stresses (Opl > 002), the maximum in-plane shear stress Tmax, and the absolute maximum shear stress tabs max on the outside surface of the pipe. Answers: Opl = i...
A pressurized pipe with an outside diameter of 13.7 in, and a wall thickness of 0.3125...
A pressurized pipe with an outside diameter of 13.7 in, and a wall thickness of 0.3125 in. is subjected to an axial force of P = 26700 lb and a torque of T = 10000 lb-ft, as shown. If the internal pressure in the pipe is 200 psi, determine the principal stresses >n2), the maximum in-plane shear stress max, and the absolute maximum shear stress Tabs mar on the outside surface of the pipe Answers: II psi. pl psi p2...
The beam shown (Figure 1) is supported by a pin at A and a cable at...
The beam shown (Figure 1) is
supported by a pin at A and a cable at B. Two
loads P = 13 kN are applied straight down from the
centerline of the bottom face. Determine the state of stress at the
point shown (Figure 2) in a section 2 m from the wall. The
dimensions are w = 5.2 cm , h = 10.5 cm ,
L = 0.8 m , a = 1.5 cm , and b = 4...
A solid circular cantilevered beam is subjected to, at the free end, a downward transverse force...
A solid circular cantilevered beam is subjected to, at the free end, a downward transverse force P, a torque T and a centric (axial) load F. Given that its diameter is 60 mm, T = 0.1P Nm and F = 10P N. (a) Determine the largest value of the load P that can be applied if the allowable stresses are 100 MPa in tension and 60 MPa in shear on a section at 120 mm from the free end. Take...
Learning Goal: The beam shown (Figure 1) is supported by a pin at A and a...
Learning Goal: The beam shown (Figure 1) is supported by a pin at A and a cable at B. Two loads P = 18 kN are applied straight down from the centerline of the bottom face. Determine the state of stress at the point shown (Figure 2) in a section 2 m from the wall. The dimensions are w = 5.4 cm , h = 12 cm, L = 0.8 m, a = 1.5 cm , and b = 4...
A pressurized pipe with an outside diameter of 11.35 in and a wall thickness of 0.375...
A pressurized pipe with an outside diameter of 11.35 in and a wall thickness of 0.375 in. is subjected to an axial force of P - 25700 lb and a torque of T = 10000 lb-ft, as shown. If the internal pressure in the pipe is 290 psi, determine the principal stresses (op 1>op 2 ), the maximum in-plane shear stresst max, and the absolute maximum shear stress tabs max on the outside surface of the pipe. Answers: Op 1...
The JT100 horizontal directional drilling machine applies 220 hp and rotates drill pipe at 100 rpm. During the drilling process, a drill pipe is subjected to the following axial and bending loads 30.0 Axial load, P, of 100 kips 0.70 ft-kips bending load, M, in the y-z plane at 30 degrees from the vertical axis The drill pipe, which is made of AISI 4130 steel, has the following dimensions and material properties (Ref. MIL-HDBK-5J, Table 2.3.1.0(c1)) » Length, L 177-in...
M15.3 Principal stresses in a rectangular tube scenes The rectangular tube is subjected to a transverse shear force of V = 230 kN and a bending moment of M = 530 kN-m, each acting in the directions shown. Determine the bending stress, the transverse shear stress magnitude, the principal stresses, and the maximum shear stress magnitude acting at location H. У Он (MPa) H 550 mm TH (MPa) 65 mm Op1 (MPa) X Op2 (MPa) 12 mm ITmax (MPa) wall...
A pressurized pipe with an outside diameter of 13.1 in. and a wall thickness of 0.375 in. is subjected to an axial force of P = 34000 lb and a torque of T = 9400 lb-ft, as shown. If the internal pressure in the pipe is 260 psi, determine the principal stresses (Opl > 002), the maximum in-plane shear stress Tmax, and the absolute maximum shear stress tabs max on the outside surface of the pipe. Answers: Opl = i...
A pressurized pipe with an outside diameter of 13.7 in, and a wall thickness of 0.3125 in. is subjected to an axial force of P = 26700 lb and a torque of T = 10000 lb-ft, as shown. If the internal pressure in the pipe is 200 psi, determine the principal stresses >n2), the maximum in-plane shear stress max, and the absolute maximum shear stress Tabs mar on the outside surface of the pipe Answers: II psi. pl psi p2...
The beam shown (Figure 1) is
supported by a pin at A and a cable at B. Two
loads P = 13 kN are applied straight down from the
centerline of the bottom face. Determine the state of stress at the
point shown (Figure 2) in a section 2 m from the wall. The
dimensions are w = 5.2 cm , h = 10.5 cm ,
L = 0.8 m , a = 1.5 cm , and b = 4...
Learning Goal: The beam shown (Figure 1) is supported by a pin at A and a cable at B. Two loads P = 18 kN are applied straight down from the centerline of the bottom face. Determine the state of stress at the point shown (Figure 2) in a section 2 m from the wall. The dimensions are w = 5.4 cm , h = 12 cm, L = 0.8 m, a = 1.5 cm , and b = 4...
A pressurized pipe with an outside diameter of 11.35 in and a wall thickness of 0.375 in. is subjected to an axial force of P - 25700 lb and a torque of T = 10000 lb-ft, as shown. If the internal pressure in the pipe is 290 psi, determine the principal stresses (op 1>op 2 ), the maximum in-plane shear stresst max, and the absolute maximum shear stress tabs max on the outside surface of the pipe. Answers: Op 1...
Most questions answered within 3 hours.
-
Write a program to score the paper-rock-scissor game. Each of
two users types in either P,R...
asked 14 minutes ago -
Calculate the equillibrium constent K for a redox reaction that
has E°cell = -.98 V at...
asked 26 minutes ago -
A concave spherical mirror has a radius of curvature of
magnitude 19.6 cm.
(a) Find the...
asked 27 minutes ago -
3. draw a diagram of the magnetic field:
a. around a long straight wire with a...
asked 26 minutes ago -
If you titrated 30.0 mL of 0.1 M HCl with 0.1 M NaOH, indicate
the approximate...
asked 35 minutes ago -
NADH passes electrons into the electron transport chain. List
the carriers that would receive the electrons,...
asked 43 minutes ago -
A cylindrical cable with a resistivity of 1.6x10-8 Ω·m and cross
sectional area of 3x10-5 m^2...
asked 43 minutes ago -
True or False.
A consumer with convex preferences who is indifferent between
the bundles (5,2) and...
asked 46 minutes ago -
A diamond's index of refraction for red light, 656 nm, is 2.410,
while that for blue...
asked 59 minutes ago -
Compare HPLC, SPE, and GC. Identify the differences, the
advantages, and the weaknesses of each method.
asked 1 hour ago -
Characteristic x-rays emitted by potassium have a wavelength of
0.374 nm. What is the energy of...
asked 1 hour ago -
there is a function to create two random numbers between 1 and
25 and a function...
asked 1 hour ago