Assume that the switch has been in position 1 for a long time, and then at time t=0 the switch is moved to position 2. Calculate i(t) fort > 0.

Question

Question

Circuit 1.

Circuit 1: Find v(0), i.e. the capacitor voltage at time 0 (in Volts). 2.4

Circuit 1: What is v(t), approximately, for extremely larget, for example, for t= 10000000 s.

Answer 1

Answer #1

for this problem, please follow the all steps that I have written above. Thank you.

Answer 2

Similar Homework Help Questions

Circuit 1. Assume that the switch has been in position 1 for a long time, and...

Circuit 1. Assume that the switch has been in position 1 for a long time, and then at time t=0 the switch is moved to position 2. Calculate i(t) fort > 0. = 06k 2 12 V ve 100 uF 3 k2 D Question 1 Circuit 1: What is the capacitor voltage fort> 0 (in Volts)? 12 exp(-0.40) 2.4 exp(-5t) 4expl-5t) 6 exp (1.2t)
7.55 The switch in the circuit of Fig. P 7.55 has been in position a for a long time. At t- 0 the switch is moved to position b. Calculate (a) the initial voltage on the capacitor; (b) the final volt...

The switch in the circuit of Fig. P 7.55 has been in position a for a long time. At t- 0 the switch is moved to position b. Calculate (a) the initial voltage on the capacitor; (b) the final voltage on the capacitor; (c) the time constant (in microseconds) for t > 0; and (d) the length of time (in microseconds) required for the capacitor voltage to reach zero after the switch is moved to position b.
The switch in the circuit in (Figure 1) has been in the left position for a long time

The switch in the circuit in (Figure 1) has been in the left position for a long time. At t = 0, it moves to the right position and stays there. Part A Select the correct expression for the capacitor voltage, v(t), fort t ≥ 0Part B Select the correct expression for the current through the 24 kΩ resistor i(t) ≥ 0+.

The switch has been in position "a" for a long time. At time t = 0

The switch has been in position "a" for a long time. At time t = 0, the switch moves from position a to position b. The switch is a "make-before-break" type: that is, the connection at position b is established before the connection at position a is broken, so there is no interruption of the current through the inductor. Questions 1. Determine the initial value of the current. 2. Determine the final value of the current and the time constant. 3. Complete Solution for...
Consider the circuit depicted in Fig. 2. The switch SW1 has been closed for a long time before it...

Consider the circuit depicted in Fig. 2. The switch SW1 has been closed for a long time before it is opened at time t = 0. The switch SW2 has been open for a long time before it is closed att = 0.1 (sec). i) Find the initial current I(0) flowing in the inductor and the initial voltage V(0) across the capacitor. ii) Find the voltage V(t) across the capacitor and the current I(t) through the inductor for 0 ≤ t ≤...
The switch has been in position a for a long time. At t=0, it instantaneously moves...

The switch has been in position a for a long time. At t=0, it instantaneously moves to position b. Find the following: a) (8-points) Voltage response b) (8-points) Current response c) (9-points) Evaluate how long after the switch is in position ‘b' does the voltage across the capacitor equal zero. 400 kA b a 2012 90 V + 40 V 60123 0.5 uF

1. The switch has been in the position shown for a long time. Find the charge...

1. The switch has been in the position shown for a long time. Find the charge on the capacitor 63 ms after the switch moves. 20 kΩ T16 V 30 kR T36 V 2. Find the current through the capacitor at t = 70 s if the circuit shown below had stabilized before the switch moved. 24ΜΩ 1V 45V
Problem 3. The switch in the following circuit has been in position for a long time...

Problem 3. The switch in the following circuit has been in position for a long time before changing at t=0. a. Find the capacitor voltage for t<0 and t>0. Sketch it. (Hint: at t=1 s the voltage is 10.8 V) b. Find the current through the capacitor for t<0 and t > 0. Sketch it. 392 22 M St=0 + - 12 v 0 400 3F - 1
1. The switch in below circuit has been in position 1 for a long time and...

1. The switch in below circuit has been in position 1 for a long time and the circuit is steady. At t-0, the switch moves to position 2. Find Vo(t) and (c) fort > 0. R1 1 W- § R2104 VaR2 60v S125K

5. In the following circuit, the switch has been in current position for a long time....

5. In the following circuit, the switch has been in current position for a long time. At t-0 s switch is moved to the second position. What is i(t) for all t>10 s? +12 V 3kn 30 V (+ 2 HF