4. A 5 cm diameter gear is driven by a 1 cm gear that rotates at...

Question

Question

Answer 1

Answer #1

4. In this case the point in contact has the same linear velocity, so: V1 = V2 Remember v = wr Then: wiri = w272 Then: W2 = w

Answer 2

Similar Homework Help Questions

5. A 5 cm diameter gear is driven by a1 cm gear that rotates at 1...

5. A 5 cm diameter gear is driven by a1 cm gear that rotates at 1 revolution per second. The 1 cm gear stalls at a torque of 1 N m. What is the stall torque of the 5 cm gear?
1. A two-stage compound gear is driven by a 20-hp motor that rotates the shaft 'a'...

1. A two-stage compound gear is driven by a 20-hp motor that rotates the shaft 'a' in CCW as shown in the figure at a speed of 100 rpm. Entire gear set has a diametral pitch of 4 teeth/in and a pressure angle of 20°. The tooth numbers are: N2 = 48, N3 = 72, N4 = 48, and Ns = 120. 5 С a 3 a. Draw the free body diagram of the compound gear 3 and 4 mounted...
2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...

2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. e) What is the transmitted force between Gears 1 and 2, in lbf? f) What is the torque of Gear 1, in in-lbf? g) What is the torque of Gear 2? h) The torque of Gear 2 and 3 are the same. What is the torque of Gear...

A wheel of diameter 50.0 cm starts from rest and rotates with a constant angular acceleration of 5.00 rad/s2.

A wheel of diameter 50.0 cm starts from rest and rotates with a constant angular acceleration of 5.00 rad/s2. At the instant the wheel has completed its second revolution, compute the radial acceleration of a point on the rim in two ways. Using the relationship arad = ω2r. From the relationship arad = v2/r.
A wheel of diameter 30.0 cm starts from rest and rotates with a constant angular acceleration of 2.50 rad/s2

A wheel of diameter 30.0 cm starts from rest and rotates with a constant angular acceleration of 2.50 rad/s2. At the instant the wheel has completed its second revolution, compute the radial acceleration of a point on the rim in two ways. Using the relationship arad = ω2r. From the relationship arad = v2/r.
A turn table of with a diameter of 36.0 cm rotates in the ccw direction. The...

A turn table of with a diameter of 36.0 cm rotates in the ccw direction. The angular acceleration is +1.75 rad/s2. After 4.00 s it has rotated through an angle of 30.0 rad. a. What is the average angular velocity? b. What is the initial angular velocity of the turntable? c. What is the magnitude of the NET linear acceleration at the outer edge of the turntable, at the start of the 4.00 s time interval?

For a short time, gear A of the automobile starter (Figure 1) rotates with an angular...

For a short time, gear A of the automobile starter (Figure 1) rotates with an angular acceleration of aA = (5001/2) rad/s?, where o is in rad/s. Determine the angular velocity of gear B after gear A has rotated 50 rev, starting from rest. The radii of gears A and B are 10 and 25 mm respectively. [4 marks) Figure 1 1 B
2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...

2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. i) What is the ratio of output torque (Gear 4) to input torque (Gear 1)? j) Is it a coincidence that it is the same as the answer in 1 An input shaft drives Gear 1 with 20 teeth at 1800 rpm which mates with the 80-tooth Gear...
Gear 2 in the figure below is driven at a speed of 1500 rpm in the...

Gear 2 in the figure below is driven at a speed of 1500 rpm in the CCW direction viewed from the right end. Gear 4 meshes with a fixed ring gear (gear 7) and with gear 5. Find the angular velocity of gear 5 in rpm. Given that, №-18 T, N3-32 T, N,-32 TN5- l0 T and N7 = 74 T 4

A compound epicyclic gear train is shown in the Figure. The shaft P is driven at...

A compound epicyclic gear train is shown in the Figure. The shaft P is driven at 2500 rpm in the clockwise direction by a motor of power rating 8 kW. The sun S2 is fixed. The number of teeth in the gears are S1, 34; S2, 21; A1, 86 and A2, 73. Determine The magnitude and direction of the angular velocity of the shaft Q and The torque required to fix the sun, S2 A, Q P S, 5,