2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...
2. Gear dynamics. The gear train above is driven on
the input shaft with a 0.5 hp electric motor.
All of the gears have a diametral pitch of 8 teeth per inch.
i) What is the ratio of output torque (Gear 4) to input torque
(Gear 1)?
j) Is it a coincidence that it is the same as the answer in 1
An input shaft drives Gear 1 with 20 teeth at 1800 rpm
which mates with
the 80-tooth Gear 2 which in on the intermediate shaft. Also on the
intermediate shaft is Gear 3
with 18 teeth. It mates with Gear 4 on the output shaft, where Gear
4 has 90 teeth.
gear train is as described
Homework Answers
Add Answer to:
2. Gear dynamics. The gear train above is driven on
the input shaft with a 0.5...
2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...
2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. e) What is the transmitted force between Gears 1 and 2, in lbf? f) What is the torque of Gear 1, in in-lbf? g) What is the torque of Gear 2? h) The torque of Gear 2 and 3 are the same. What is the torque of Gear...
2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...
2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. a) What are the diameters of Gears 1, 2, 3, and 4? b) What is the pitch-line velocity of Gear 1, in ft/min? c) Is the pitch-line velocity of Gear 2 the same as Gear 1? d) What is the pitch-line velocity of Gear 3 (and, therefore, Gear...
1. Gear kinematics. An input shaft drives Gear 1 with 20 teeth at 1800 rpm which...
1. Gear kinematics. An input shaft drives Gear 1 with 20 teeth at 1800 rpm which mates with the 80-tooth Gear 2 which in on the intermediate shaft. Also on the intermediate shaft is Gear 3 with 18 teeth. It mates with Gear 4 on the output shaft, where Gear 4 has 90 teeth. a) How fast does Gear 2 spin, in rpm? b) Gears 2 and 3 spin at the same speed, so what is the speed of Gear...
Homework 6: The figure below shows a gear train where gear 1, on shaft a (input...
Homework 6: The figure below shows a gear train where gear 1, on shaft a (input shaft), drives gear 2 with 32 teeth (denoted 32T) on shaft b, gear 3 (20T) also is on shaft b and drives gear 4 (507) on shaft c (output shaft). The pitch diameter of gears 1 and 2 are d = 24 mm and d = 48 mm. The center distance between gears 3 and 4 (distance between shafts b and c is 70mm....
Show all work. A compound reverted gear train will be used to decrease speed with a...
Show all work.
A compound reverted gear train will be used to decrease speed with a ratio of 36 to 1. In the figure below, the input shaft drives gear 5, and the output shaft is driven by gear 2. Use spur gears with a 20 degree pressure angle and a diametral pitch of 5 teeth / in. a) Specify the appropriate numbers of teeth for both gear sets to minimize the gearbox size, while also avoiding gear tooth interference....
1. A two-stage compound gear is driven by a 20-hp motor that rotates the shaft 'a'...
1. A two-stage compound gear is driven by a 20-hp motor that rotates the shaft 'a' in CCW as shown in the figure at a speed of 100 rpm. Entire gear set has a diametral pitch of 4 teeth/in and a pressure angle of 20°. The tooth numbers are: N2 = 48, N3 = 72, N4 = 48, and Ns = 120. 5 С a 3 a. Draw the free body diagram of the compound gear 3 and 4 mounted...
Problem 1. Design a reverted gear train for a transmission with three speeds and reverse. For...
Problem 1. Design a reverted gear train for a transmission with three speeds and reverse. For an input speed of 450 rpm to the driving shaft (green), the driven shaft (teal) should have output forward speeds of 75, 300, and 450 rpm, and an output reverse speed of 150 rpm. Assume all gears have a diametral pitch of 10. Gear A (24 teeth) and Gear D (36 teeth) are in constant mesh. Determine the numbers of teeth for ALL six...
A compound epicyclic gear train is shown in the Figure. The shaft P is driven a...
A compound epicyclic gear train is shown in the Figure. The
shaft P is driven a 4000 rpm in the clockwise direction by a motor
of power rating of 10W . The annulus A2 is fixed. The
number of teeth in the gears are , S1,28;
S2,21; A1,72 and A2,99 .
Determine:
The magnitude and direction of the angular velocity of the
shaft Q
The torque required to fix the annulus, A2
A, A₂ P, P2 P P. z S
Answer the following questions about the illustrated gear train. Assume the input shaft has an angular...
Answer the following questions about the illustrated gear train. Assume the input shaft has an angular velocity of 100RPM CCW and 100lb-ft of torque. Show all work and circle answers. (a) (5 points) What is the overall gear ratio between the input and output shaft?! (b) (5 points) What is the torque of the output shaft assuming an ideal system? (c) (5 points) What is the direction that the output shaft is rotating? Clockwise CWyor counterclockwise (CCW)? Draw the direction...
A compound epicyclic gear train is shown in the Figure. The shaft P is driven at...
A compound epicyclic gear train is shown in the Figure. The
shaft P is driven at 2500 rpm in the clockwise direction by a motor
of power rating 8 kW. The sun S2 is fixed. The number of teeth in
the gears are S1, 34; S2, 21; A1, 86 and A2, 73. Determine
The magnitude and direction of the angular velocity of the
shaft Q and
The torque required to fix the sun, S2
A, Q P S, 5,
Homework 6: The figure below shows a gear train where gear 1, on shaft a (input shaft), drives gear 2 with 32 teeth (denoted 32T) on shaft b, gear 3 (20T) also is on shaft b and drives gear 4 (507) on shaft c (output shaft). The pitch diameter of gears 1 and 2 are d = 24 mm and d = 48 mm. The center distance between gears 3 and 4 (distance between shafts b and c is 70mm....
Show all work.
A compound reverted gear train will be used to decrease speed with a ratio of 36 to 1. In the figure below, the input shaft drives gear 5, and the output shaft is driven by gear 2. Use spur gears with a 20 degree pressure angle and a diametral pitch of 5 teeth / in. a) Specify the appropriate numbers of teeth for both gear sets to minimize the gearbox size, while also avoiding gear tooth interference....
1. A two-stage compound gear is driven by a 20-hp motor that rotates the shaft 'a' in CCW as shown in the figure at a speed of 100 rpm. Entire gear set has a diametral pitch of 4 teeth/in and a pressure angle of 20°. The tooth numbers are: N2 = 48, N3 = 72, N4 = 48, and Ns = 120. 5 С a 3 a. Draw the free body diagram of the compound gear 3 and 4 mounted...
Problem 1. Design a reverted gear train for a transmission with three speeds and reverse. For an input speed of 450 rpm to the driving shaft (green), the driven shaft (teal) should have output forward speeds of 75, 300, and 450 rpm, and an output reverse speed of 150 rpm. Assume all gears have a diametral pitch of 10. Gear A (24 teeth) and Gear D (36 teeth) are in constant mesh. Determine the numbers of teeth for ALL six...
A compound epicyclic gear train is shown in the Figure. The
shaft P is driven a 4000 rpm in the clockwise direction by a motor
of power rating of 10W . The annulus A2 is fixed. The
number of teeth in the gears are , S1,28;
S2,21; A1,72 and A2,99 .
Determine:
The magnitude and direction of the angular velocity of the
shaft Q
The torque required to fix the annulus, A2
A, A₂ P, P2 P P. z S
Answer the following questions about the illustrated gear train. Assume the input shaft has an angular velocity of 100RPM CCW and 100lb-ft of torque. Show all work and circle answers. (a) (5 points) What is the overall gear ratio between the input and output shaft?! (b) (5 points) What is the torque of the output shaft assuming an ideal system? (c) (5 points) What is the direction that the output shaft is rotating? Clockwise CWyor counterclockwise (CCW)? Draw the direction...
A compound epicyclic gear train is shown in the Figure. The
shaft P is driven at 2500 rpm in the clockwise direction by a motor
of power rating 8 kW. The sun S2 is fixed. The number of teeth in
the gears are S1, 34; S2, 21; A1, 86 and A2, 73. Determine
The magnitude and direction of the angular velocity of the
shaft Q and
The torque required to fix the sun, S2
A, Q P S, 5,
Most questions answered within 3 hours.
-
An aspirin dose of 5.0mg per kg of body weight has been
prescribed to reduce the...
asked 2 minutes ago -
The AASB Conceptual Framework (2.12-2.19) refers to ‘faithful
representation’ as being necessary for financial information to...
asked 7 minutes ago -
A U.S. corporation with net receivables in euro could hedge by
_________________.
A. buying euro forward...
asked 9 minutes ago -
Consider the following reversible reaction: CO2 +
H2O <--> H2CO3.In which
direction (right or left) will...
asked 12 minutes ago -
Which of the following probabilities indicates a relationship
that is not statistically significant?
Group of answer...
asked 13 minutes ago -
QUESTION 8
Which layer of the TCP/IP hierarchy presents incoming messages
to the computer user?
a....
asked 20 minutes ago -
A solenoid a cross-sectional area of 5.4x10^-4 m^2, consists of
540 turns per meter, and carries...
asked 31 minutes ago -
Explain some of the pros and cons of converting a C Corporation
into an S Corp?...
asked 35 minutes ago -
The diagram below shows a meter shunted by a parallel resistance
Rs. The maximum value for...
asked 35 minutes ago -
Be sure to answer all parts. A solution contains 0.107 mol of
NaCl dissolved in 9.35...
asked 34 minutes ago -
1. An 25.96 g sample of aluminum is placed on a 45.15 g sample
of copper...
asked 44 minutes ago -
Calculate the mass of p-dichlorobenzene (mm=147.00 g/mol) that
when dissolved in 125 ml cyclohexane (d=0.779 g/mol,...
asked 52 minutes ago