ZuoTi.Pro
Question

6sSSM An elevator cable is to be made of a new type of composite developed by Acme Laboratories. In the lab, a sample of the cable that is 2 m long and has a cross-sectional area of 0.2 mm fails under a load of 1000 N. The cable in the elevator will be 20 m long and have a cross-sectional area of 1.2 mm2. It will need to support a load of 20,000 N safely Will it?

science   physics   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

1.2升 Y 3.yio the c-be Cek

0 0
Add a comment
Know the answer?
Add Answer to:
6sSSM An elevator cable is to be made of a new type of composite developed by...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • At a building site, a 1000 kg container hangs from a crane cable and is then...

    At a building site, a 1000 kg container hangs from a crane cable and is then placed on the floor so that the cable is unloaded. The container is pushed to an elevator shaft, where it is to be lowered by the crane. By mistake, there is a 1-m slack in the cable from the crane when the container is pushed into the elevator shaft. Calculate the maximum stress in the cable if the cable has a cross-sectional area of...

  • Link BD is made of brass (E 105 GPa) and has a cross-sectional area of 240...

    Link BD is made of brass (E 105 GPa) and has a cross-sectional area of 240 mm2. Link CE is made of aluminium (E 72 GPa) and has a cross-sectional area of 300 mm2. Knowing that they support rigid member ABC, determine the maximum force P that can be applied vertically at point A if the deflection of A is not to exceed 0.36 mm. (Round the final answer to two decimal places.) 995 mm A 150 mm E 225...

  • Q1: A fiberglass composite is composed of a matrix of vinyl ester and reinforcing fibers of...

    Q1: A fiberglass composite is composed of a matrix of vinyl ester and reinforcing fibers of E-glass. The volume fraction of E-glass is 31%. The remainder is vinyl ester. The density of the vinyl ester is 0.651 g/cm3, and its modulus of elasticity is 4.89 GPa. The density of E-glass is 2.685 g/cm3, and its modulus of elasticity is 71 GPa. A section of composite 1.00 cm by 25.00 cm by 200.00 cm is fabricated with the E-glass fibers running...

  • Question 4 1 pts A wire made from a composite material is shaped into a cylinder...

    Question 4 1 pts A wire made from a composite material is shaped into a cylinder and is stretched by a machine pulling in opposite directions at the two ends of the wire. The wire has an initial length of 1.20 m and an initial cross-sectional area of 9.00 x 10-6m2. If a force of 450 N stretches it by 2.1 mm and the wire returns to its original shape after being stretched, what is the Young's Modulus of the...

  • 1. A composite beam is made of wood and reinforced with a steel strap located on...

    1. A composite beam is made of wood and reinforced with a steel strap located on its bottom side. It has the cross-sectional area shown in the given Figure. Given the beam is subjected to a bending moment of M 2 kN m and the material properties wood and steel are, E Esteel 200 GPa, respectively, determine the of wood 12 GPa and 150 mm normal stress at points B and C (20 points) 20 mm

  • the axial load ? ldtlcs & Strength Material r is supported by the pin-connected rod CB that has a cross-sectional 1. The rigid ba area of 16 mm2 and is made from 6061-T6 aluminum. Determine th...

    the axial load ? ldtlcs & Strength Material r is supported by the pin-connected rod CB that has a cross-sectional 1. The rigid ba area of 16 mm2 and is made from 6061-T6 aluminum. Determine the ax the rod CB and elongation rod CB. (E 68.9 GPa, v 0.35) ial stress at 300 N m 1.5 m 0) ldtlcs & Strength Material r is supported by the pin-connected rod CB that has a cross-sectional 1. The rigid ba area of...

  • 4. Referring to Figure 26.0, a magnetic circuit core is made of stalloy and has and...

    4. Referring to Figure 26.0, a magnetic circuit core is made of stalloy and has and air gap of 1.2 mm. An exciter coil of 400-turn is wound at the center limb. The center limb cross sectional area is 1600 mm and the cross sectional area of both sides of limb is 1000mm?. Calculate the current required to establish a flux of 1000 uWb in the air gap. Neglect fringing effect and flux leakage. The B-H curve for stalloy is...

  • 2063 0.9 m 9000 N Aluminum Composite Panel (ACP) is a type of flat panel that...

    2063 0.9 m 9000 N Aluminum Composite Panel (ACP) is a type of flat panel that consists of two thin aluminum sheets bonded to a non-aluminum core. ACPs are frequently used for external cladding of buildings (building facades), for insulation and for signage. Epcot's Spaceship Earth is an example of the use of ACP in architecture. It is a geodesic sphere composed of 11,324 ACP tiles. A 0.9 m long by 9 mm thick panel is constructed of two 0.4...

  • 2063 0.9 m 9000 N Aluminum Composite Panel (ACP) is a type of flat panel that...

    2063 0.9 m 9000 N Aluminum Composite Panel (ACP) is a type of flat panel that consists of two thin aluminum sheets bonded to a non-aluminum core. ACPs are frequently used for external cladding of buildings (building facades), for insulation and for signage. Epcot's Spaceship Earth is an example of the use of ACP in architecture. It is a geodesic sphere composed of 11,324 ACP tiles. A 0.9 m long by 9 mm thick panel is constructed of two 0.4...

  • A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...

    A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT