Qualitative influence line method P16.16 Reaction at B, shear force at section 1-1, and bending moment...

Question

Question

P16.16 Reaction at B, shear force at section 1-1, and bending moment at 2-2. (Ans: load P16.9 12 12 Problem 16.9

Qualitative influence line method

Answer 1

Answer #1

2 6 ft 3) quanh rive しM1-2) A- 2-2

Answer 2

Similar Homework Help Questions

Qualitative influence line method Moment at D and B; shear force at C. Moment crelease D...

Qualitative influence line method Moment at D and B; shear force at C. Moment crelease D Problem 16.14
Qualitative influence lines method P16.11 Vertical reaction and moment at A; shearing force and bend- ing...

Qualitative influence lines method P16.11 Vertical reaction and moment at A; shearing force and bend- ing moment at section 1-1. (Ansa lea Problem 16.11
Question 2: A simply supported beam under loading as shown in Figure 1: 1. Draw the influence lines of the bending moment and shear force at point C (L/4) Using the influence lines to determine t...

Question 2: A simply supported beam under loading as shown in Figure 1: 1. Draw the influence lines of the bending moment and shear force at point C (L/4) Using the influence lines to determine the bending moment and shear force at section C due to the loading as shown in the figure. 2. 3. There is a distributed live load (w#2.5kN/m) which can vary the location along the beam. Determine the location of the live loads which create the...

Problem #2 6-7. Draw the influence lines for (a) the moment at B (b) the shear...

Problem #2 6-7. Draw the influence lines for (a) the moment at B (b) the shear at B, and (c) the vertical reaction at A. Solve this problem using the basic method of Sec. 6.1. Hint: The support at C resists only a horizontal force and a bending moment.
1) Draw the influence lines for the reaction force at A, the shear force at C...

1) Draw the influence lines for the reaction force at A, the shear force at C and the moment at C. Show all the values. faA 2m 2 m 2 m 2) The Beam of problem #1 is subjected to uniform dead load 0.8 kN/m and uniform live load of 2 kN/m and a single live concentrated force of 20 kN. Determine (a) the maximum reaction force at A, (b) the maximum positive shear at point C, and (c) the...
Ningbo University of Technology test papers VII. Construct the influence line for the bending moment on...

Ningbo University of Technology test papers VII. Construct the influence line for the bending moment on section C of the following beam due to unit load transmitted via panel points by using tae method. (15 points) P=1 A B C 2m 2m Ningbo University of Technology test papers VII. Construct the influence line for the bending moment on section C of the following beam due to unit load transmitted via panel points by using tae method. (15 points) P=1 A...

2. Draw Shear Force and Bending Moment Diagram (use your preferred method). Determine Maximum Ten...

2. Draw Shear Force and Bending Moment Diagram (use your preferred method). Determine Maximum Tensile and Compressive Stresses due to bending, state where on the beam these occur. For the mid-point between A and B, determine shear stress at neutral axis; 2" from the top of the flange; at the junction between web and flange and on the top of the flange for the cross-section. Plot of the bending stress and shear stress distribution diagram across the cross section of...
Draw the shear force and bending moment diagrams for the following three beams using the graphical method

1. Draw the shear force and bending moment diagrams for the following three beams using the graphical method 2. For beams (a) and (b) in problem 1, find the shear and moment functions using the method of sections.
1-Draw the influence line for: a) b) c) d) e) The moment at A The shear...

1-Draw the influence line for: a) b) c) d) e) The moment at A The shear force at C The moment at C The vertical Reaction at B The moment at B

Determine the shear force and bending moment in the beam.

Question 1 options:Determine the shear force and bending moment in the beam. Use F1 = 1550 N, F2 = 1350 N, M=450 N.m, and a = 3.5 m.The shear force in the section AC in N is (round to the nearest integer): ____ NThe shear force in the section CD in N is (round to the nearest integer):___NThe shear force in the section DE in N is (round to the nearest integer):___NThe shear force in the section EB in N...