Example: Aliguld is the hydraulic line shown. A 50 block sits on the larger piston. The...
How far must a 2.0-cm-diameter piston be pushed down into one cylinder of a hydraulic lift to raise an 7-cm-diameter piston by 30 cm?
please answer all 4 questions, please write clear 4. If the pressure in the thermometer abo temperature? ve was 121 kPa, to the nearest Celsius degree what is the 9. The cross-sectional area of the output piston in a hydraulic device is 10 times the area of the input piston. By how much can the device multiply the input force? The cross-sectional area of the output piston in a hydraulic device is 3.0 times the area of the input piston....
A hydraulic lift is used to jack a 950-kg car 42 cm off the floor. The diameter of the output piston is 17 cm , and the input force is 360 N . What is the area of the input piston? What is the work done in lifting the car 42 cmcm ? If the input piston moves 13 cmcm in each stroke, how high does the car move up for each stroke? How many strokes are required to jack...
S.A hydraulic lift is lifting a car that weighs 14 kN. The area of the piston supporting the car is A, the area of the other piston is A, and the ratio A/A, is 108.5. How far must the small piston be pushed down to raise the car a distance of 2.0 em? [Hint: Consider the work to be done.] A. 2.17 cm B. 14 m A. C. 14 cm D. 2.17 m Hydraulic fluid 7. A clock has a...
Consider the hydraulic jack represented beside. It is filled with mineral oil (a lubricating liquid). Assume that a person is able to push the left piston (F1) with a maximum force of 343 N. The diameter of the piston on the left is only 2 cm and that of the piston on the right much larger at 40 cm. • A) If the piston on the right is used to lift a car, what is the highest car weight (in...
To work on your car you use a hydraulic lift as shown in the diagram. It confines a fluid with ρ = 2.16 kg/m3.Your car has mass Mcar = 980 kg. The lift piston has mass Mpiston = 225 kg. The input piston (on the left) is massless and has an area of 0.785 m2. The lift piston (on the right) has an area of 4.14 m2. 1. The lift piston base and the input piston base are at the...
A hydraulic lift is used to jack a 940-kg car 42 cm off the floor. The diameter of the output piston is 19 cm , and the input force is 360 N . A) What is the area of the input piston? Express your answer using two significant figures. B)What is the work done in lifting the car 42 cm ? Express your answer using two significant figures. C)If the input piston moves 14 cm in each stroke, how high...
A 14,192-N car is raised using a hydraulic lift, which consists of a U-tube with arms of unequal areas, filled with incompressible oll with a density of 900 kg/m3 and capped at both ends with tight-fitting pistons. The wider arm of the U-tube has a radius of 19.3 cm and the narrower arm has a radius of 3 cm. The car rests on the piston on the wider arm of the U-tube. The pistons are initially at the same level....
In a water pistol, a piston drives water through a larger tube of radius 1.30 cm into a smaller tube of radius 1.50 mm as in the figure below. (a) If the pistol is fired horizontally at a height of 1.40 m, use ballistics to determine the time it takes water to travel from the nozzle to the ground. (Neglect air resistance and assume atmospheric pressure is 1.00 atm. Assume up is the positive y-direction. Indicate the direction with the...
0/2 points 1 Previous Anowers SerCP119 4P 009 My Notes O Ask Your Teas (a) Calculate the absolute pressure at the bottom of a fresh-water lake at a depth of 23.4 m. Assume the density of the water is 1.00 x 10" kg/m and the air above is at a pressure of 101.3 kPa. 330 6 Your response is off by a multiple of ten. Pa (b) What force is exerted by the water on the window of an underwater...