Water to a residential area is transported at a rate of 1.5 m3/s via 70-cm-internal-diameter concrete...
Water to a residential area is transported at a rate of 1.5 m3/s via 70-cm-internal-diameter concrete pipes with a surface roughness of 3 mm and a total length of 1500 m. In order to reduce umping power requirements, it is pro posed to line the interior surfaces of the concrete pipe with 2-cm-thick petroleum-based lining that has a surface rough ness thickness of 0.04 mm. There is a concern that the reduc tion of pipe diameter to 66 cm and...
fluid mechanics ASAP please Problem 4 (50 points) Water is discharged from a reservoir at a rate of 18.103 m3/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses...
Water, with density of 1000 kg/m3 and kinematic viscosity of 1.0 x 10- m2/s, is pumped through a total length of 60 m of pipe from a lower reservoir to a higher reservoir. The inner diameter of the pipe is 30 cm. Both reservoirs are open to the atmosphere, and the water surface of the higher reservoir is 10 m above that of the lower reservoir. The entrance from the lower reservoir to the pipe is sharp-edged, and along the...
Question 11 Water is flowing through a 10-cm-diameter water pipe at a rate of 0.2 m3/s. Now a diffuser with an outlet diameter of 20 cm is bolted to the pipe in order to slow down water that exits into atmosphere, as shown. Disregarding frictional effects, determine the force exerted on the flange due to the water flow. Density of water = 1000 kg/m3 = 10 cm D = 20 cm Diffuser 357 N 1549 N 6205 N none of...
Question 11 Water is flowing through a 10-cm-diameter water pipe at a rate of 0.2 m3/s. Now a diffuser with an outlet diameter of 20 cm is bolted to the pipe in order to slow down water that exits into atmosphere, as shown. Disregarding frictional effects, determine the force exerted on the flange due to the water flow. Density of water = 1000 kg/m3 -. + d = 10 cm D = 20 cm Diffuser 357 N 1549 N 6205...
Problem 4 (50 points) water is discharged from a reservoir at a rate of 18.103 m2/s using two horizontal cast iron pipes nected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses associated with the connection...
lunzontal pipe and pump system in the following figure discharges 0.01583 m3/s. The gage pressure iust before the pressure is 400 The m/s2 losses between 20°C water at 57 m3/h 0 kPa and just after the pump the gage a. The pump inlet diameter is 9 cm and the outlet diameter is 3 em. Let g-9.81 pump is 12 o Pwater9 kg/m, Hwate0.001002 kgm-s) and Pat the two pressure points and the pump. But consider frictional losses at the 9-cm...
Water at 15°C (ρ = 999.1 kg/m3and μ = 1.138 × 10−3 kg/m·s) is flowing steadily in a 34-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine the pressure drop, the head loss, and the pumping power requirement to overcome this pressure drop. The roughness of stainless steel is 0.002 mm.Determine the following:A)The pressure drop in _______ kPa.B)The head loss in _______ m.C)The pumping power requirement in _______ kW.
The required water flow rate in the 6 cm diameter 30-meter long circular pipe in the diagram below is 12 liters per second. The water temperature is 4 °C and the flow discharges into the atmosphere at a pressure of PB = 100 kPa. The flow is fully developed turbulent flow and there is no elevation change. The surface of the wall has become degraded due to pitting and deposits such that there is a surface roughness with a height...
Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m/s. Then, a diffuser with an outlet diameter of 20 cm is bolted to the pipe in order to slow down water as it exits the diffuser to atmospheric pressure, as shown in the given figure. Disregarding frictional effects, determine the force exerted on the bolts due to the water flow. Take the density of water to be 1000 kg/m3 -t- d 10 cmm D = 20...