Water at 15°C (ρ = 999.1 kg/m3and μ = 1.138 × 10−3 kg/m·s) is flowing steadily in a 34-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine the pressure drop, the head loss, and the pumping power requirement to overcome this pressure drop. The roughness of stainless steel is 0.002 mm.
Determine the following:
A)The pressure drop in _______ kPa.
B)The head loss in _______ m.
C)The pumping power requirement in _______ kW.
Water at 15°C (ρ = 999.1 kg/m3 and μ = 1.138 × 10−3 kg/m·s) is flowing steadily in a 34-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine the pressure d...
8-31 Water at 10°C (p = 999.7 kg/m3 and μ = 1.307 × 10-3 kg/m.s) is flowing steadily in a 0.20-cm-diameter, 15-m-long pipe at an average velocity of 1.2 m/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop. Answers: (a) 188 kPa, (b) 19.2 m, (c) 0.71 W 8-32 Water at 15°C (p = 999.1 kg/m3 and μ = 1.138 × 10-3 kg/m . s) is flowing steadily in a 30-m-long...
Water at 15 degrees celcius is flowing steadily in a 5cm horizontal pipe made of stainless steel (roughness 0.22mm) at a rate of 6L/s. For a 60m long pipe. Determine head loss due to friction, the pressure loss in Kpa and required pumping power in kw.
Water at 10 °C (p = 999.7kg/m3 and μ = 1.307×10-3kg/ms) is flowing steadily in a 0.12-cm-diameter, 15-m-long pipe at an average velocity of 0.9 m/s. Determine (a) the Reynolds number and decide weather the flow is laminar or turbulent (b) the head loss, (c) the pressure drop, and (d) the pumping power requirement to overcome this pressure drop.
3) Water at 15°C (p- 999.7 kg/m3 and u 1.307 x 10-3 kg/m-s) is flowing steadily in a 0.25-cm diameter, 35-m-long pipe at an average velocity of 1.2 m/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
Water (p = 1000 kg/m3 and u = 1.002X10-3 kg/m.s) is flowing steadily in a 30 m-long and 5 cm-diameter inclined pipe ( = 40% made of stainless steel (ε = 0.002mm) at a rate of 9 L/s. Determine: 1. The pressure drop (P1-P) 2. The pumping power requirement to overcome this pressure drop. 5cm 9 L/s L 30 m
Air enters a 10-m-long section of a rectangular duct of cross section 15 cm X 20 cm made of commercial steel at an average velocity of 7 m/s.(p = 1.145kg/m3 ,μ = 1.895x10-5kg/ms) and e=0.000045 m). For this pipe determine (a)the Reynolds number and decide weather the flow is laminar or turbulent (b) the head loss, (c) the pressure drop, and (d) the pumping power requirement to overcome this pressure drop.
Water at 15 degree Celsius , density = 999kg/cubic meter, viscosity = 0.001138 kg/ms , is flowing steadily in a 5 cm diameter horizontal pipe made of stainless steel at a rate of 0.006 m3/s . Determine the pressure drop, the head loss and the required pumping power input for flow over a 60m long section of the pipe.
you have water that flows stationary in a horizontal pipe 0.2667m in diameter, made of stainless steel at a rate of 20 lt / s. Determine the head loss and pressure drop M = 1.14x10 ^ -6 m2 / s, if the pipe is 1 km long
lunzontal pipe and pump system in the following figure discharges 0.01583 m3/s. The gage pressure iust before the pressure is 400 The m/s2 losses between 20°C water at 57 m3/h 0 kPa and just after the pump the gage a. The pump inlet diameter is 9 cm and the outlet diameter is 3 em. Let g-9.81 pump is 12 o Pwater9 kg/m, Hwate0.001002 kgm-s) and Pat the two pressure points and the pump. But consider frictional losses at the 9-cm...
A flow nozzle equipped with a differential pressure gage is used to measure the flow rate of water at 10°C (p 9997 kg/m3 and p 1.307 x 10-3 kg/m s) through a 3-cm-diameter horizontal pipe. The nozzle exit diameter is 1.5 cm, and the measured pressure drop is 3.3 kPa. Determine the volume flow rate of water, the average velocity through the pipe, and the head loss 1.5 cm Differential pressure gage -3 m3(s m/s The volume flow rate of...