Water at 10 °C (p = 999.7kg/m3 and μ = 1.307×10-3kg/ms) is flowing steadily in a 0.12-cm-diameter, 15-m-long pipe at an average velocity of 0.9 m/s. Determine
(a) the Reynolds number and decide weather the flow is laminar or turbulent
(b) the head loss,
(c) the pressure drop, and
(d) the pumping power requirement to overcome this pressure drop.
Water at 10 °C (p = 999.7kg/m3 and μ = 1.307×10-3kg/ms) is flowing steadily in a 0.12-cm-diameter, 15-m-long pipe at an average velocity of 0.9 m/s. Determine
8-31 Water at 10°C (p = 999.7 kg/m3 and μ = 1.307 × 10-3 kg/m.s) is flowing steadily in a 0.20-cm-diameter, 15-m-long pipe at an average velocity of 1.2 m/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop. Answers: (a) 188 kPa, (b) 19.2 m, (c) 0.71 W 8-32 Water at 15°C (p = 999.1 kg/m3 and μ = 1.138 × 10-3 kg/m . s) is flowing steadily in a 30-m-long...
3) Water at 15°C (p- 999.7 kg/m3 and u 1.307 x 10-3 kg/m-s) is flowing steadily in a 0.25-cm diameter, 35-m-long pipe at an average velocity of 1.2 m/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
Air enters a 10-m-long section of a rectangular duct of cross section 15 cm X 20 cm made of commercial steel at an average velocity of 7 m/s.(p = 1.145kg/m3 ,μ = 1.895x10-5kg/ms) and e=0.000045 m). For this pipe determine (a)the Reynolds number and decide weather the flow is laminar or turbulent (b) the head loss, (c) the pressure drop, and (d) the pumping power requirement to overcome this pressure drop.
Water at 15°C (ρ = 999.1 kg/m3and μ = 1.138 × 10−3 kg/m·s) is flowing
steadily in a 34-m-long and 6-cm-diameter horizontal pipe made of
stainless steel at a rate of 10 L/s. Determine the pressure drop,
the head loss, and the pumping power requirement to overcome this
pressure drop. The roughness of stainless steel is 0.002 mm.Determine the following:A)The pressure drop in _______ kPa.B)The head loss in _______ m.C)The pumping power requirement in _______ kW.
Water (p = 1000 kg/m3 and u = 1.002X10-3 kg/m.s) is flowing steadily in a 30 m-long and 5 cm-diameter inclined pipe ( = 40% made of stainless steel (ε = 0.002mm) at a rate of 9 L/s. Determine: 1. The pressure drop (P1-P) 2. The pumping power requirement to overcome this pressure drop. 5cm 9 L/s L 30 m
5.16. Water is flowing in a 3-cm-diameter pipe at an average velocity of Uav 2 m/s. Assuming water density of ρ-1000 kg/m 3 and viscosity μ-10-3 N s'm2, calculate the velocity at the center of the pipe, the shear τ at the wall, and the Reynolds number. Assuming laminar flow, calculate friction coefficient C and pressure drop dp/dx.
A flow nozzle equipped with a differential pressure gage is used to measure the flow rate of water at 10°C (p 9997 kg/m3 and p 1.307 x 10-3 kg/m s) through a 3-cm-diameter horizontal pipe. The nozzle exit diameter is 1.5 cm, and the measured pressure drop is 3.3 kPa. Determine the volume flow rate of water, the average velocity through the pipe, and the head loss 1.5 cm Differential pressure gage -3 m3(s m/s The volume flow rate of...
Water at 15 degree Celsius , density = 999kg/cubic meter, viscosity = 0.001138 kg/ms , is flowing steadily in a 5 cm diameter horizontal pipe made of stainless steel at a rate of 0.006 m3/s . Determine the pressure drop, the head loss and the required pumping power input for flow over a 60m long section of the pipe.
H2.3 Consider water at 20°C flowing through a horizontal pipe of diameter 15 cm and length 10 m. The flowrate is 0.021 m3/s and the wall shear stress is 5.76 N/m2. Assume fully developed flow. a. Verify that the flow is turbulent b. Determine the pressure drop [N/m2 c. Estimate the viscous sublayer thickness [mm], i.e., where y+ 5 d. Compare results of part c. with typical pipe roughness (see Table 8.1 in text and comment on implication e. Using...
40 N"s/m2 and ?-1000 kg/m3 is flowing through a circular pipe umetric flow rate (Q) of the oil is 1*10 m'/s, determine: 1) (2096) Oil with viscosity of with diameter D 0 0.1 m. If the volu a. b. If the flow is laminar or turbulent Th e pressure drop over a 20 m length of p ipe in kPa