Homework Answers
1)Some diluted acid is transferred to a clean, dry beaker.
2) The concentration of the original stock acid is calculated.
3) 20mL portions of stock acid is quantitatively transferred into a 100mL volumetric flask.
4) The 100mL volumetric flask containing 20mL of stock acid is filled to the mark stepwise with swirling.
5) The 100mL volumetric flask is stoppered and inverted with swirling multiple times.
6) 20mL portions of diluted acid are quantitatively transferred into Erlenmeyer flasks.
7) The diluted samples are tittrated to a phenolphthalein endpoint using NaOH solution.
8) The concentration of the diluted acid is calculated.
Add Answer to:
Place the events occurring during the Dilution in Analysis experiment into correct order some diluted acid...
Electrolytes, Concentration and Dilution of Solutions n this part of the experiment, you will make a dilution of a stock solution of known concentration and calculate the concentration of the di...
Electrolytes, Concentration and Dilution of Solutions n this part of the experiment, you will make a dilution of a stock solution of known concentration and calculate the concentration of the dilute solution. DILUTION OF A STOCK SOLUTION PART C: Measurements and Observations Procedure Check out a 100-mL volumetric flask from your instructor. Fill test tube about 2/3 concentration of the active ingredient from its label including units. Record 1. orlt O " concentration of active ingredient. full of "Magic 2....
can someone help me with the first and the second matching questions A 10.00 ml pipette...
can someone help me with the first and the second matching
questions
A 10.00 ml pipette delivers portions of a diluted vinegar solution into 3 separate Erlenmeyer flasks, then the acetic acid is titrated using a standard solution of 0.060 M NaOH to a phenolphthalein end point. The results of the three trials are given below. What was the average M (mol/L) of the diluted vinegar? Trial # Vinegar Volume (mL) Initial Buret Volume (mL) Final Buret Volume (mL) 1...
Concentration of NaOH = 1600 x10- Molar Sodium hydroxide Nach Trial 1 Trial 2 Trial Trial 4 2.60/1.20 1...
Concentration of NaOH = 1600 x10- Molar Sodium hydroxide Nach Trial 1 Trial 2 Trial Trial 4 2.60/1.20 11.40/1.30 28.20 29.10.26.1026.50 Initial buret reading Final buret reading Volume of NaOH added Moles of NaOH added Moles of HCl reacted Molarity of diluted HCI Molarity of undiluted HCI Average molarity of undiluted HCI Precision PROCEDURE 1. Obtain approximately 40 mL of an unknown acid in an Erlenmeyer flask from your teaching assistant. 2. Clean your 250-ml volumetric flask (contains exactly 250.00...
Concentration of NaOH = 1600 x10- Molar Sodium hydroxide Nach Trial 1 Trial 2 Trial Trial...
Concentration of NaOH = 1600 x10- Molar Sodium hydroxide Nach Trial 1 Trial 2 Trial Trial 4 2.60/1.20 1.40/1.30 28.20 29.10.26.1026.50 Volume of NaOH added Initial buret reading Final buret reading Moles of NaOH added Moles of HCl reacted Molarity of diluted HCI Molarity of undiluted HCI Average molarity of undiluted HCI Precision PROCEDURE 1. Obtain approximately 40 mL of an unknown acid in an Erlenmeyer flask from your teaching assistant. 2. Clean your 250-ml volumetric flask (contains exactly 250.00...
Data the experiment Record For the lab report, attach this data sheet (signed by your TA) to your...
please write out calculations for each box missing an answer
data the experiment Record For the lab report, attach this data sheet (signed by your TA) to your calculations page. REPORT ALL VALUES TO AT LEAST THREE SIGNIFICANT FIGURES. READ YOUR BURETTE TO THE NEAREST 0.05 mL increment. for on this sheet. Do your calculations on a separate piece of paper. Part One-Standardization of a NaOH solution of approximately 0.1 M. Trial 1 | Trial 2 | Trial 3 Mass...
Water Hardness by EDTA Titration Objective: To determine [Ca2+,MG2+] and [Mg2+] concentration in an unknown water...
Water Hardness by EDTA Titration Objective: To determine [Ca2+,MG2+] and [Mg2+] concentration in an unknown water sample A 0.0107 molarity solution of EDTA is prepared for the experiment. 25 mL of an unknown is pipetted and diluted 100 mL with distilled water and adjusted to a pH between 8 and 10 with NH4OH. A 10.00 mL portion of the diluted unknown is transferred to a 250 mL flask with 3 mL of pH 10 ammonia buffer and tiny amount of...
I need it right now, please help me?? PROCEDURE PART I: DILUTING THE VINEGAR SOLUTION The...
I
need it right now, please help me??
PROCEDURE PART I: DILUTING THE VINEGAR SOLUTION The vinegar solution must be diluted by a factor of 5 to be suitable for titration. 1. Obtain - 20 ml of the stock vinegar solution from the fume hood. 2. Using the 10-ml. pipet, pipet" 10 mL of the stock solution to a 50-ml volumetric flask. 3. Fill the volumetric flask to the calibration line with distilled water. Be sure not to go over...
ALL THE INFO YOU NEED IS BELOW average volume of NaOH: 15.7 mL or 0.0157 L...
ALL THE INFO YOU NEED IS BELOW
average volume of NaOH: 15.7 mL or
0.0157 L
average number of moles of NaOH added:
6.28*10-4 moles
molar concentration of [HT] in saturated solution(HT–
acts as a monoprotic acid, reacting with NaOH in a 1:1 ratio
(Volume of KHT measured using 25.00 mL volumetric pipet.)):
0.2512 M
Analysis of KHT in water
1. Weigh out 0.8 grams of potassium hydrogen tartrate (KHT) on
weighing paper. Add the KHT to a clean dry...
Prelab Questions 1. a. (10) Determine the a) mass of the solute and b) volume of conc. HCl you are going to a) wei...
Prelab Questions 1. a. (10) Determine the a) mass of the solute and b) volume of conc. HCl you are going to a) weigh out and b) measure with a graduated cylinder to create 1L of 100.0 ppm stock solution of Acetylsalicylic acid (ASA) (from the pure powder) in a 2%(W/V) HCI. Show your calculation. C at:.. HALI Procedure - External Standards 1. First make 2% V/v HCI. You will make this three times. Transfer to two plastic containers (use...
Pre-Lab Questions The titration curve below (on the next page) was obtained by titrating 25.00 mL...
i need help with pre-lab questions
Pre-Lab Questions The titration curve below (on the next page) was obtained by titrating 25.00 mL of a boric acid solution with a 1.000 M NaOH solution. Use the information given on the titration curve to answer the following questions: 1. What is the formula and value of K, for boric acid? Calculate using the half equivalence data point, and using the pH at one-quarter and three-quarter points, too. What is the average Ka...
Electrolytes, Concentration and Dilution of Solutions n this part of the experiment, you will make a dilution of a stock solution of known concentration and calculate the concentration of the dilute solution. DILUTION OF A STOCK SOLUTION PART C: Measurements and Observations Procedure Check out a 100-mL volumetric flask from your instructor. Fill test tube about 2/3 concentration of the active ingredient from its label including units. Record 1. orlt O " concentration of active ingredient. full of "Magic 2....
can someone help me with the first and the second matching
questions
A 10.00 ml pipette delivers portions of a diluted vinegar solution into 3 separate Erlenmeyer flasks, then the acetic acid is titrated using a standard solution of 0.060 M NaOH to a phenolphthalein end point. The results of the three trials are given below. What was the average M (mol/L) of the diluted vinegar? Trial # Vinegar Volume (mL) Initial Buret Volume (mL) Final Buret Volume (mL) 1...
Concentration of NaOH = 1600 x10- Molar Sodium hydroxide Nach Trial 1 Trial 2 Trial Trial 4 2.60/1.20 11.40/1.30 28.20 29.10.26.1026.50 Initial buret reading Final buret reading Volume of NaOH added Moles of NaOH added Moles of HCl reacted Molarity of diluted HCI Molarity of undiluted HCI Average molarity of undiluted HCI Precision PROCEDURE 1. Obtain approximately 40 mL of an unknown acid in an Erlenmeyer flask from your teaching assistant. 2. Clean your 250-ml volumetric flask (contains exactly 250.00...
Concentration of NaOH = 1600 x10- Molar Sodium hydroxide Nach Trial 1 Trial 2 Trial Trial 4 2.60/1.20 1.40/1.30 28.20 29.10.26.1026.50 Volume of NaOH added Initial buret reading Final buret reading Moles of NaOH added Moles of HCl reacted Molarity of diluted HCI Molarity of undiluted HCI Average molarity of undiluted HCI Precision PROCEDURE 1. Obtain approximately 40 mL of an unknown acid in an Erlenmeyer flask from your teaching assistant. 2. Clean your 250-ml volumetric flask (contains exactly 250.00...
please write out calculations for each box missing an answer
data the experiment Record For the lab report, attach this data sheet (signed by your TA) to your calculations page. REPORT ALL VALUES TO AT LEAST THREE SIGNIFICANT FIGURES. READ YOUR BURETTE TO THE NEAREST 0.05 mL increment. for on this sheet. Do your calculations on a separate piece of paper. Part One-Standardization of a NaOH solution of approximately 0.1 M. Trial 1 | Trial 2 | Trial 3 Mass...
I
need it right now, please help me??
PROCEDURE PART I: DILUTING THE VINEGAR SOLUTION The vinegar solution must be diluted by a factor of 5 to be suitable for titration. 1. Obtain - 20 ml of the stock vinegar solution from the fume hood. 2. Using the 10-ml. pipet, pipet" 10 mL of the stock solution to a 50-ml volumetric flask. 3. Fill the volumetric flask to the calibration line with distilled water. Be sure not to go over...
ALL THE INFO YOU NEED IS BELOW
average volume of NaOH: 15.7 mL or
0.0157 L
average number of moles of NaOH added:
6.28*10-4 moles
molar concentration of [HT] in saturated solution(HT–
acts as a monoprotic acid, reacting with NaOH in a 1:1 ratio
(Volume of KHT measured using 25.00 mL volumetric pipet.)):
0.2512 M
Analysis of KHT in water
1. Weigh out 0.8 grams of potassium hydrogen tartrate (KHT) on
weighing paper. Add the KHT to a clean dry...
Prelab Questions 1. a. (10) Determine the a) mass of the solute and b) volume of conc. HCl you are going to a) weigh out and b) measure with a graduated cylinder to create 1L of 100.0 ppm stock solution of Acetylsalicylic acid (ASA) (from the pure powder) in a 2%(W/V) HCI. Show your calculation. C at:.. HALI Procedure - External Standards 1. First make 2% V/v HCI. You will make this three times. Transfer to two plastic containers (use...
i need help with pre-lab questions
Pre-Lab Questions The titration curve below (on the next page) was obtained by titrating 25.00 mL of a boric acid solution with a 1.000 M NaOH solution. Use the information given on the titration curve to answer the following questions: 1. What is the formula and value of K, for boric acid? Calculate using the half equivalence data point, and using the pH at one-quarter and three-quarter points, too. What is the average Ka...
Most questions answered within 3 hours.
-
Write a program to solve the Josephus problem, with the following
modification:
Sample Input:
./a.out n...
asked 1 hour ago -
At the start of a CD it is spinning at a rate of 525 rpm
(revolutions...
asked 2 hours ago -
4. Without doing any calculations, predict whether the observed
∆T would increase, decrease or remain the...
asked 3 hours ago -
Based on the range, which of the following sets of scores has
the greatest variability? 3,...
asked 4 hours ago -
Ripples in a pond travel at a velocity of 3 m/s with one peak
passing a...
asked 4 hours ago -
A man stands on the roof of a building of height 13.0 mm and
throws a...
asked 4 hours ago -
The extent to which assets are financed by borrowed funds and
other liabilities is indicated by:...
asked 5 hours ago -
Explain in detail
Germany is the fifth largest economy
explain what goods and services Germany specializes...
asked 6 hours ago -
The density of platinum is 21.45 g/mL. If a cube of platinum
with a mass of...
asked 6 hours ago -
Accounts Receivable
Sales
A/R Posting
Extended Sales Invoice
Packing Slip
Compare invoice to packing slip 2...
asked 6 hours ago -
Michaella, age 23, is a full-time law student and is claimed by
her parents as a...
asked 6 hours ago -
Why are polymers not typically casted into products?
asked 6 hours ago