Analysis questions part 1 and part 2. Data and Calculations- Length, Mass, Volume, Density and Time...
1.3 Metric Measurements (Length) The metric unit for measuring length is the meter. In this exercise, students will measure the leng th of various objects. Procedure . How many Obtain a small metric ruler. How many centimeters are shown on the ruler? 1. millimeters are shown? Measure the length of your index finger to the nearest mm. How long is your finger? 2. Select three small wooden blocks. Measure the length, width, and height of each block in cm. Record...
Objectives To make basic measurements of length, mass and time To practice graphing using spreadsheet software and paper and pencil. 1. Lenght Estimate the length of a meter by putting a pen or pencil at one end of a table and placing a second pen or pencil about one meter away from the first. Use the meter tape measure to measure the actual length of your meter estimate. Record the length of your meter estimate Calculate the percent error of...
Rule Part 1: Measurement of Volume and Density: - Imm Data: Fill in your measurements in the table below. Be sure to indicate the units for each measurement. (Hint: a given object should have the same dimensions measured with any tool. If this is not the case, check your units) 7 + NLAH WWA WA Inner Outer Table 2 Measurement of Assorted Objects length (mm) Width/ mm height mm Diameter uncertainty u m (mm) Measured using Ruler Rectangular 49 30...
Prepare a table. These are the values I got. 4] Prepare a table for your volume and density measurements. You have to present the volumes and densities for the cylinder calculated using the two instruments. Refer to the tutorial How to prepore a table to know how to prepare a table for the physics labs. Your table should contain columns for the measuring instruments, the volumes (in mm3) and the densities (in kg/m3). Don't forget to incdlude uncertainties! Data sheet...
I need someone to help answer table 1 only mass, volume, y density and table 2 with a graph each table. please read the procesures, thank you Experiment 2 Graphing and Measurements Graphs summarize numerical data efficiently and are usually casier to understand and interpret than columns of numbers. In this experiment, you will collect data and construct a graph that makes an effective visual presentation. Materials: Equipment metric ruler Chemical a kit with 5 pieces Procedure: Part I: Measurements...
Insert Table Chart Text Shape Media Comment Volume Table 4: Mass Set Density Data Quantity Height (cm) Base Edge Length, b (cm) Volume, V (cm3) Mass (g) Measurement 2.3cm 2.5cm 37.35cm 3 100 g 2.68g/cm^3 Uncertainty 0.05cm- 0.05cm/- N/A 10 g N/A Density (g/c3) Post-Lab Questions Table 5: Known Densities of Various Materials Density at 20*C 2.70 g/cm 8.92 g/cm 11.34 g/cm 8.90 g/cm 10.50 g/cm Material Aluminu Copper Lead Nickel Silver
figure 2.3 EXPERIMENT Experimental Uncertainty (Error) and Data Analysis 2 Laboratory Report TI QUESTIONS 1. Read the measurements on the rulers in Fig. 2.9, and comment on the results Ruler 1 om 5 Ruler 2 cm 6 Ruler 3 TTm 6 Figure 2.9 2. Were the measurements of the block in part tb) of Procedure 2 all done with the same instrument? Explain. 3. Referring to the dart analogy in Fig. 2.3, draw a dart grouping that would represent poor...
Can somebody help me with my lab report question 1? nalysis: Your lab report should include the following: In the "Calculations" section: 1. Using your measurements of the dimensions of the room, calculate lume of the room. Also calculate the uncertainty in the volume given your estimated uncertainties in the length, width and height. 2. Determine the area of the table for both sets of measurements (ruler and meter stick), and calculate the uncertainty in the area using both sets...
Table 2. Dimensions of 250g Hanging Mass Base Edge (cm) (hexagonal mass)* Base Diameter (cm) (cylindrical mass)* Height (cm) 2.3 N/A 5.7 *Fill in the column that corresponds to the mass provided in your kit. You will have EITHER a hexagonal mass or a cylindrical mass, not both. Table 3. 250 g Hanging Mass Buoyancy Data Object Weight in Air (N) Weight in Water (N) Buoyancy Force (N) Volume Displaced (mL) 250 g Hanging Mass 2.5 2.1 0.4 22 Rubber...
DATA SHEET: LAB IV Measurements and Density Determination 14. Volume of metal piece 2 by water displacement: 19.8ml (calculate) 15. Initial volume of water in graduated cylinder: 10.5 mL 16. Volume of water and metal piece 3: 40.6 ml 17. Volume of metal piece 3 by water displacement: 30.ImL (calculate) PART D. Quantitative and Empirical Skills Density - Mass/Volume 18. Densities of metal pieces 1, 2 and 3: .918g/ml 10l1g/mL .997 (calculate for each metal piece) 9 19. Average density...