Alright Dude, If that worked for you... dont forget to give THUMBS UP.(that will work for me!)
If I missed something feel free to leave a comment.
atleast before giving downvote.
and, Thanks for using homeworklib- Smarter way to study.
4. Example 2.11-Equilibrium of a Particle A strut CB is guyed back to a wall support...
Determine the magnitudes of F1, F2, and F3 for equilibrium of the particle. The applied forces and Q are applied at point O. Given P = 2.8 + xx (kN) and Q = 8.5 + xx (kN), where xx is the last two digits of your student ID number. If your student ID is 6x-XXXXXX-xxx1-2, P = 2.8 + 12 = 14.8 kN and Q = 8.5 + 12 = 20.5 kN. F2 30° 25 15 P 1.1 Force Q...
2.50
Two slender links, AC and BC, extend from a wall and support a pulley at C. A cable, tied at D, passes over the small pulley at C and experience an 80-lb force at its free end E. If the pulley is frictionless and of negligible determine the forces developed in members AC and BC. An inextensible (cannot stretch) cable AC and spring CB are originally horizontal. A 100-N weight is attached to point C, and the system is...
(a) Warren truss (b) Howe truss (c) Pratt truss (d) Baltimore truss (e) Parker truss Figure 2: Truss Types (Nielson Text) The truss bridge has the following properties/characteristics: 1. Span length (bottom chord): 168 ft 2. 14 panels (12 ft length per panel) 3. All diagonals are 45 degrees 4. Simple truss (all members are pin-connected and loads are only applied at the joints) 5. Simply-supported (pin at one end, roller at the other) 6. 13 ft width between trusses...
Please answer all parts of the questions and please
try making them clear and easy to understand.
CONCEPTUAL QUESTIONS: (Total Points 10, 1 points each question) 1- A plate is supported by a bal-and-socket joint at A, a roller joint at B, and a cable at C. How many unknown support reactions are there in this problem? 300 N 400 N i m A) Four forces and two moments B) Six forces C) Five forces D) Four forces and one...
please help! I need help finding and solving equations of
equilibrium to find the max tension in the cables and the angle
that results in the maximum tension, I also have pictures below of
the work I have so far all I really need is equations for the 4
cable part and that's it but I put the whole assignment so you
could see thanks!
Tower Support System Challenge Challenge Scenario: Due to weather conditions, a major communication tower n...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...