Prepare 1L of a 7.5% dextrose solution using sterile water for injection (SWFI) and 10% dextrose...

Question

Question

Prepare 1L of a 7.5% dextrose solution using sterile water for injection (SWFI) and 10% dextrose solution. How much of each is required?

Answer 1

Answer #1

We required 1 Litre of 7.5%. dextrose solution from 10% dextrose solution & SW EI, Hene. 7.54. for lline, 75 ml for loom/ of

Answer 2

Similar Homework Help Questions

.7) A solution containing 500,000 units of polymyxin B sulfate in 20 mL of sterile water for injection is added to...

.7) A solution containing 500,000 units of polymyxin B sulfate in 20 mL of sterile water for injection is added to 500 mL of 5% dextrose injection. The infusion is to be administered over 2.5 hours. If the administration set calibrates 10 drops/mL. At what rate, in drops per minute, should the flow be adjusted to administer the infusion over the designated time interval? (Do not ignore volume contribution due to admixture).
can anyone help me answer 4 (with work) thank you How many mL of a 3% solution can be made from 27grams of drug? 3, loo 3 9 ML Answer- How many mL's of a 50% dextrose solution and sterile wate...

can anyone help me answer 4 (with work) thank you How many mL of a 3% solution can be made from 27grams of drug? 3, loo 3 9 ML Answer- How many mL's of a 50% dextrose solution and sterile water for injection (SWE) would be required to compound 2 liters of a 12% dextrose solution? 4. Answer A patient is admitted for the treatment of DVT and is being started on a heparin drip. If the patie 209 lbs.,...
1. A TPN order calls for a liter of solution to contain 3.5% of amino acids...

1. A TPN order calls for a liter of solution to contain 3.5% of amino acids and 15% of dextrose. How many milliliters each of 8.5% amino acid injection, 70% dextrose injection, and sterile water for injection should be used to prepare the solution?

An order for an intravenous solution (IV) is written as follows: Dextrose (anhydrous) 2.5% (E =...

An order for an intravenous solution (IV) is written as follows: Dextrose (anhydrous) 2.5% (E = 0.18) KCl 1.49 g (E = 0.76) NaCl q.s. Sterile Water for Injection (SWI) q.s. ad 500 mL Which of the following best describes this solution? Place either A, B, or C as the answer. This solution is: A. Hypotonic B. Isotonic C. Hypertonic How is this determined?
Preparation #5: Formula (Reconstitution for IM injection per manufacturer): Ceftriaxone 250mg/mL IM injection Ceftriaxone Dry Powder...

Preparation #5: Formula (Reconstitution for IM injection per manufacturer): Ceftriaxone 250mg/mL IM injection Ceftriaxone Dry Powder for Injection 1-g vial Sterile Water for Injection According to the manufacturer's instructions, to achieve a concentration of 250- mg/mL, reconstitute the 1-gram vial with 3.6-mL of diluent (SWFI, NS,D5W,etc). Procedure: Perform all necessary calculations and gather equipment and supplies. (No Calculations for this procedure) Aseptically introduce containers and supplies into the PEC. • Carefully remove the plastic cap from each vial. Disinfect the...
Dakins’ solution is prepared using bleach and sterile water for irrigation. If the final concentration is...

Dakins’ solution is prepared using bleach and sterile water for irrigation. If the final concentration is 0.25% how much hypochlorite should you add to a 2000ml bottle?

UyU lulen? 3. Using the component sources as indicated, calculate the amount of each component required...

UyU lulen? 3. Using the component sources as indicated, calculate the amount of each component required in preparing 1000 mL of the following parenteral nutrition solution: Parenteral Nutrition Solution Formula (a) Amino Acids 2.125% (b) Dextrose 20% (c) Sodium Chloride 30 mEq (d) Calcium Gluconate 2.5 mEq (e) Insulin 15 units (f) Heparin 2500 units (g) Sterile Water for Injection to make 1000 mL Component Source 500 mL of 8.5% amino acids injection 500 mL of 50% dextrose injection 20-mL...
2- if 60 g of 1% hydrocortisone is mixed with 80 g of 2.5% hydrocortisone, what...

2- if 60 g of 1% hydrocortisone is mixed with 80 g of 2.5% hydrocortisone, what is the percent W/W of hydrocortisone in the final mixture? 10 - How would 500 ml bag of 3% 50/50 be prepared using 3%sodium chloride, sodium acetate 2 meq/ml, and sterile water for injection. 9- How many g of the drug are required to dispense one pint of 1 in 25 solutions 7- How many g of g of sodium chloride should be used...
How would you prepare 500 mL of a 5% D5W (dextrose in water) solution from a 29%...

How would you prepare 500 mL of a 5% D5W (dextrose in water) solution from a 29% stock solution?

Preparation #5: Ceftriaxone 250mg/mL IM injection Formula (Reconstitution for IM injection per manufacturer): Ceftriaxone Dry Powder...

Preparation #5: Ceftriaxone 250mg/mL IM injection Formula (Reconstitution for IM injection per manufacturer): Ceftriaxone Dry Powder for Injection 1-g vial Sterile Water for Injection According to the manufacturer's instructions, to achieve a concentration of 250- mg/mL, reconstitute the 1-gram vial with 3.6-mL of diluent (SWFI, NS,D5W,etc). Procedure: • Perform all necessary calculations and gather equipment and supplies. (No Calculations for this procedure) • Aseptically introduce containers and supplies into the PEC. Carefully remove the plastic cap from each vial. Disinfect...