ANSWER THE FOLLOWING QUESTION AND DRAW THE FIGURE WHERE REQUIRED. PROVIDE EACH & EVERY STEP
ANSWER THE FOLLOWING QUESTION AND DRAW THE FIGURE WHERE REQUIRED. PROVIDE EACH & EVERY STEP The...
The stepped rod shown below is made of three uniform elements. The rod was intended to be welded to, and exactly fit between, the rigid walls at A and D. However, member 2 was manufactured an amount d2 too short. First the entire rod is stretched so that its ends can be welded to the rigid walls. Then, an axial load PB is applied to the rod at B and member (3) is heated by an amount AT3. Write a...
Problèm GIVEN b 2) Three rod elements shown above are stress free when they are assembled together and attached to the rigid walls A and D. Element (1) is steel with E1 30 x 103ksi, cross - sectional area Ai - 2.0 in, length L1-80 in and coefficient of thermal expansion α1=7x10-6/0F; the corresponding values for the aluminum element (2) are: E2 10 x 103ksi, A2-3.6 in, L,- 60 in, a2 13 x 10-6/oF; the corresponding values for the bronze...
Q1 An elastic cantilever beam of varying cross section, as shown in Figure Q1(a), is subjected to an increase in temperature of 60°C in an unnatural environment. The equation governing the displacement of the elastic column and the finite element stiffness matrix are respectively given as -O and ΑΕ) - where A is the cross sectional area of the beam, E is the Young's modulus of the beam material, u is the displacement and / is the finite element length....
Please solve this question clearly and step by step.
Thank you
2. A truss assembly shown in Figure Q2 below is made of aluminum alloy that has a modulus of elasticity, E = 69 GPa. member is 225 mm2 The cross sectional area of each 4300 N (0, 40) m (40, 40) m 2 500 N 3 (0, 0) FIGURE Q2 Determine the global stiffness matrix for the truss assembly. a. [10 marks] Determine the displacement at node 3. b....
finite element methods question. I need the answer immediately pls
help
Question 2) 50 Points: Consider a truss structure that is built 300 N from two identical truss elements. For the truss elements, the modulus of elasticity is E = 69 GPa, and the cross-section area is A = 968 mm². Assume that the origin (0,0) is at Node 1 and C (2000) elements 1 and 2 are connected as 1-3 and 3-2, respectively. 500N Considering the forces 300 N...
We were unable to transcribe this imageProblem 1 The truss (all joints are pinned) structure in figure 1 is made of members with cross sectional area A = 1 in, with a linear elastic, homogeneous, isotropic material with an elastic modulus. E-10E6 psi and a coefficient of thermal expansion, α-6E-6 °F-ι. The structure starts out at a uniform temperature of 65°F and is raised to a final temperature of 120°F while being subjected to a concentrated load Po- 5,000 lbs...
Grid 4 Grid 3 Po 15 in Grid 1 Grid 2 10 in Figure 1: Problem 1 Schematic Problem 1 The truss (all joints are pinned) structure in figure 1 is made of members with cross sectional area A- 1 in2, with a linear elastic, homogeneous, isotropic material with an elastic modulus, E, 10E6 psi and a coefficient of thermal expansion. α-6E-6 op-1. The structure starts out at a uniform temperature of 65°F and is raised to a final temperature...
Do
case #4
Background: The data shown on the following page was obtained from Tension Tests of 10 unknown ductile metals. For each test, various dimensions and loads were measured before and after failure. The data is a summary of readings taken during the test (loads vs extensometer readings). Purpose: To determine the stress, strain, yield stress and modulus of elasticity of a circular shaped specimen from a tension test. Directions: A. For your particular case (depending on your last...
can anyone help me with this test please? I'm struggling with it QUESTION 1 A permanently installed overhead strip light is a ____. a.foot light b.track light c.border light d.head light QUESTION 2 Egress lighting for carnivals, circuses and fairs shall not ____. a.contain metal raceways b.be integrated into a central switchboard c.contain branch circuits d.be protected by a GFCI protection device QUESTION 3 The attachment plug cap in a mobile home shall be a ____, rated 50...
How
do I solve this?
Problem 2(50 points) The roof of the Edwin A. Stevens building is to be redesigned to accommodate a billboard for Stevens Institute of Technology. The new billboard will weigh 40 kips and be supported equally by two columns located 9 ft from the rear of the building. The beams supporting the new roof will be simply supported as shown. (Note there is a 5 ft overhang at the front of the building). For the grade...