Choice of unit load is determined by the:
Choice of unit load is determined by the:
Homework Answers
The choice of unit load is determined by various factors. However the key factor for the choice of unit load is the nature and characteristics of goods that is passed along the supply chain. This is why when shipping steel the unit load may be different from shipments of food items.
Relationship of per unit efficiency and per unit regulation in a transformer with load at a...
Relationship of per unit efficiency and per unit regulation in a transformer with load at a unity power factor?
Would the determined "Thevenin and Norton equivalents" be valid for atty value of "load resistor" that...
Would the determined "Thevenin and Norton equivalents" be valid for atty value of "load resistor" that may be connected between points A and B? Please provide verbal solution
Please show me step by step how to get load impedance in per-unit. New load is 1.05+1.4j per unit...
Please show me step by step how to get load impedance in
per-unit. New load is 1.05+1.4j per unit and new z load is 0.447
per unit
Consider the three-phase power system in the figure below. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances, including the load impedance in per-unit. Lines 1 and 2 have series reactances of 48.4 and 65.43 2, respectively. At bus 4,...
The general lighting load (expressed as a unit load per square foot) for a warehouse is...
The general lighting load (expressed as a unit load per square foot) for a warehouse is OA. IVA/sq ft ○ B. 1/4VAsqft ° C. 1/8VA/sqft ○ D. 1-12VA/sqft
Q5 2 Points If load is applied on the unit cell with the largest unit cell...
Q5 2 Points If load is applied on the unit cell with the largest unit cell edge length, the material slips along (1 -1 OJ. Find all the slip systems in this unit cell that contains this direction. Draw separate unit cells to show the direction and the corresponding planes that make the slip system. Enter your answer here Please select file(s) Select file(s) Q6 2 Points If one manufactures a wire of 6 cm diameter out of this single...
It has been determined that a point in a load-carrying member is subjected to the following...
It has been determined that a point in a load-carrying member is subjected to the following 2. stress condition: Tay 200MPa(CW) O 400MPA ay-300MPA (a) Draw the initial stress element. (b) Draw the complete Mohr's circle, labeling critical points. (c) Draw the complete principal stress element. (d) Draw the maximum shear stress element.
The per-unit impedance of a short-transmission line is ?0.06. The per-unit load on the line is...
The per-unit impedance of a short-transmission line is ?0.06. The per-unit load on the line is (1 + ?0.6) ?? at a receiving end voltage of 1∠0° ??. Calculate the average power flow over the line.
An economist would say that the benefits of regional integration are determined by Multiple Choice the...
An economist would say that the benefits of regional integration are determined by Multiple Choice the formation of a political union. the amount of trade diversion. the amount of trade creation. the level of consumer involvement. the location of manufacturing facilities.
Venue is determined by: Multiple Choice State statute. The trial judge. The trial jury. The United...
Venue is determined by: Multiple Choice State statute. The trial judge. The trial jury. The United States Constitution. Case Law.
Liquidity is largely determined by: Multiple Choice the account receivable cycle. the account payable cycle. the...
Liquidity is largely determined by: Multiple Choice the account receivable cycle. the account payable cycle. the credit term. the cash flow cycle.
Please show me step by step how to get load impedance in
per-unit. New load is 1.05+1.4j per unit and new z load is 0.447
per unit
Consider the three-phase power system in the figure below. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances, including the load impedance in per-unit. Lines 1 and 2 have series reactances of 48.4 and 65.43 2, respectively. At bus 4,...
The general lighting load (expressed as a unit load per square foot) for a warehouse is OA. IVA/sq ft ○ B. 1/4VAsqft ° C. 1/8VA/sqft ○ D. 1-12VA/sqft
Q5 2 Points If load is applied on the unit cell with the largest unit cell edge length, the material slips along (1 -1 OJ. Find all the slip systems in this unit cell that contains this direction. Draw separate unit cells to show the direction and the corresponding planes that make the slip system. Enter your answer here Please select file(s) Select file(s) Q6 2 Points If one manufactures a wire of 6 cm diameter out of this single...
It has been determined that a point in a load-carrying member is subjected to the following 2. stress condition: Tay 200MPa(CW) O 400MPA ay-300MPA (a) Draw the initial stress element. (b) Draw the complete Mohr's circle, labeling critical points. (c) Draw the complete principal stress element. (d) Draw the maximum shear stress element.
Liquidity is largely determined by: Multiple Choice the account receivable cycle. the account payable cycle. the credit term. the cash flow cycle.
Most questions answered within 3 hours.
-
Dealing with conflict, in my opinion, is a skill and an art. I
believe that those...
asked 15 minutes ago -
6. A long straight wire with circular cross section and radius
1.5 cm carries a 1.2...
asked 19 minutes ago -
Deacon Corporation has provided the following financial data
from its balance sheet and income statement:
Year...
asked 1 hour ago -
List and discuss at least three variables from everyday life for
which you expect the variable ...
asked 1 hour ago -
A high-pass filter consists of a 1.60 μF capacitor in series
with a 125 Ω resistor....
asked 1 hour ago -
A newly developed artificial intelligence has trouble
distinguishing hand-written numbers from hand-written alphabets.
There are pictures...
asked 1 hour ago -
The carbonate ion CO3 2- has multiple resonance structures.
a. Draw them and assign the hybridization...
asked 1 hour ago -
In doing an allocation for a basket purchase
Use the individual costs and the total market...
asked 1 hour ago -
what were the social political and economic causes and impacts of
the late 19th century urban...
asked 1 hour ago -
if the magnitude of a velocity vector is 10m/s and it
makes an angle of 45...
asked 1 hour ago -
Which amino acid has a basic R group?
A) tyrosine
B) Isoleucine
C) Glutamic Acid
D)...
asked 1 hour ago -
Is there the need for the government to have hackers. Please
share your thoughts.
asked 1 hour ago