Problem 2 (25 points) A rectangular reinforced concrete beam has a width b-15 inches and effecti...
A rectangular reinforced concrete beam of span 16 ft supports a concentrated load of 40 kips at mid-point of the beam and a uniformly-distributed load of 4 kips/ft over the entire span. Given: (a) The breadth of the beam is 18 inches. (b) Concrete compressive strength, fc, is 3500 psi. (c) Rebar is Grade 40 steel i) Determine the maximum moment and maximum shear acting on the beam. ii) Determine the minimum effective depth 'd' of the beam section (rounded...
A rectangular reinforced concrete beam of span 16 ft supports a concentrated load of 40 kips at mid-point of the beam and a uniformly-distributed load of 4 kips/ft over the entire span. Given: (a) The breadth of the beam is 18 inches. (b) Concrete compressive strength, f 'c, is 3500 psi. (c) Rebar is Grade 40 steel i) Determine the maximum moment and maximum shear acting on the beam. ii) Determine the minimum effective depth 'd' of the beam section...
A reinforced concrete beam shown in Figure below is 15-in. wide and has effective depth of31 in. The factored loads are shown. (The factored uniform load includes the weight of the beam). Design the web reinforcement using the Vu diagram shown in the Figure (for a symmetric half). Assume No. 3 stirrups,fc '-4000 psi and fy=fyt-60000psi. 100 kip 100 kip d-31 in. 15 ft clear span As s) 102.5 kip se 2.5 ki @y、阪、もw cl.* 3..-K: ps A reinforced concrete...
A rectangular beam having b=16 in and d=26 in spans 28 ft face to face of simple supports. It is reinforced for flexure with 6#11 bars that continue uninterrupted to the ends of the span. It is to carry service dead load 2.0 kips/ft (including self weight) and service live load 3.6 kips/ft, both uniformly distributed along the span. Design the shear reinforcement using vertical U stirrups. Economize the spacing of stirrups in appropriate number of bands. Material strengths are...
15 points 9. A rectangular concrete beam of width b=24 in. is limited by architectural considerations to a maximum total depth h=16 in. It must carry a total factored load moment Mu 400 k-ft. Design the flexural reinforcement for this member, using compression steel if necessary. Allow 3-in, to the center of the bars from the compression or tension face of the beam. Material strengths are fy=60 ksi and fc=4 ksi. Select reinforcement to provide the needed areas, complete necessary...
A reinforced concrete beam has the following properties: Beam width, b = 320 mm Effective depth, d = 640 mm Concrete strength, f’c = 21 MPa Reinforcing steel strength, fy = 400 MPa If the factored shear force at the critical section is 210,000 N, compute the nominal shear carried by the shear reinforcement. EXERCISE - USD SHEAR 1. A reinforced concrete beam has the following properties: Beam width, b = 320 mm Effective depth, d = 640 mm Concrete...
simply supported reinforced concrete beam of rectangular section is hung on the left end by a 400mm square post working in tension, as shown in the figure below. The beam supports a uniform dead load (DL) gf 100 KN/m (excluding its own weight) and upiform live load LL) of 40KN/m. The beam is reinforced with 025 longitudinal rebars with 40mm cleat cover to the stirrups. Material properties: fy 420 MPa, fe 25 MPa. Beam dimension b 400mm and h 600mm....
Problem 1: A reinforced concrete beam having the cross section shown is on a simple span of 26.5ft. It has already been estimated that the applied factored moment, Mu, is 700 k-ft. Assume 60ksi. interior exposure, #3 stirrups, f'e 3ksi, fy Required: 1) Analyze if the beam is adequate for moment only. (3 points) Solution: 91 34.4" d 38" 6u-7 4.#9 (4) Problem 1: A reinforced concrete beam having the cross section shown is on a simple span of 26.5ft....
Reinforced Concrete Design Please answer it with good write . Problem 1: The reinforced concrete cantilever beam shown is subjected to a concentrated load P- 2 kips, at its free end. Determine the development length of the shown bars using the detailed and simplified methods for the following cases: a) straight bars b) 90 hooks c )180, hooks The column width is 22 inches. Concrete cover is measured from the concrete surface to the center of the reinforcement. fc 4...
A rectangular steel-reinforced concrete beam supports a uniformly distributed load of 875 lb/ft (including the beam weight) for a span of 24 ft. The breadth of the beam is 12 in. Concrete with a specified compressive of 3000 lb/sqin and grade 60 steel for tensile and web reinforcement are specified. Four longitudinal tensile bars are to be used. If required, No. 3 stirrups will be used. Determine the minimum effective depth of the beam section (Round to the nearest inch...