Just want to make sure Selective Reject ARQ Sender Receiver Frame 0 Frame 1 Frame 2...
Layout the time flow diagram for both Go-Back-N and Selective
Repeat
ARQ mechanism in the following given scenario.
Sender Receiver A B Frame o ACK 1 Frame 1 ACK 2 Frame 2 Lost Frame 3 ACK 3 ACK 4 Time Time
The question has parts: a,b,c,d and e.
Intro. To Telecommunications Assign#4 (d) Suppose the same situation as above but sender and receiver use Selective Repeat ARQ What frame(s) would the sender need to retransmit? Explain. 1. Suppose that a sender and a receiver are using ARQ to perform reliable data delivery. (a) In a Go-Back-N ARQ protocol, the window size is 6. Frames with sequence numbers 1, 2, 3, 4 and 5 have been sent. The sender just received an...
(a) Assume a Sliding Window with Go-Back N ARQ is being used on a transmission link with a 3-bit sequence number. The transmitter has previously sent frames with sequence numbers 0, 1 and 2. Is the transmitter allowed to send a frame with sequence number 3 if the frame with sequence number 2 has not been acknowledged? Explain your answer. (b) Assume a Sliding Window with Go-Back N ARQ is being used on a transmission link with a 3-bit sequence...
TCP at Packet Level In a TCP packet level data transfer, sender and receiver both have a window that can hold 4 packets. Sender has 5 packets to send numbered 0-4. ACK 2 is lost and PKT 3 is lost too. (Remember in TCP the ACK number is one greater than the number of the last packet received in order and that ACKs are cumulative) There are no other errors or losses in either direction. Draw a timeline diagram that...
1. For TCP end-to-end flow control, suppose the capacity of the
receiver buffer is 10 packets. Suppose the packets that are being
queued in the receiver buffer are packets 4, 5, 6, 7, 8, 10, 11.
What is the advertised window size the receiver sent to the sender?
Suppose packet 12 is the last packet sent by the sender. What’s the
effective window size at the sender? Can the sender send out packet
13 at this moment? How about packet...
just want to make sure this is correct
Write the expression as a sum and/or difference of logarithms. Express powers In (x12 15-x).0 <x<5 In (x+2 V5-x) = 24 In x + In (5-x) 2 (Simplify your answer.)
1. (1 pt) Under what conditions would an open-loop protocol such as an error-correcting Hamming code be preferable to the feedback type protocols discussed in Chapter 3? 2. (1 pt) Suppose that a stop-and-wait protocol was used on a channel has a 300 millisecond propagation delay and sender frames sizes of 100 milliseconds. The receiver must fully receive the frame before sending an acknowledgment. The size of the acknowledgment can be ignored. What is the channel utilization? 3. (1 pt)...
please answer fast and neatly . please make sure its
right
1 Hash (10 pts) m Alice Bob t = CRC(m) Attacker 'Y' or 'N' = V(m,t) 1. Describe the security vulnerability of the system provided above. (3 pts) 2. What is the solution for the problem found in Problem 1? (3 pts) 3. One example of the solution that was found in Problem 2 is "Hash Message Authentication Code (MAC)." Describe the operation principle of hash MAC at (i)...
Please give me a detailed and easy to follow assumptions. Please
make no assumptions and if you could take me baby steps to get the
answer across don't hesitate. Thank you in advance
2.) In class we showed how shift registers can transfer information between chips on a single wire. It requires the sender to do the operation sequence Load, Shift, Shift, Shift" and repeat, while the receiver always shifts, but reads the values every 4 cycles (cycle 5, 9,...
To save time, I already have the equations, I just want to make
sure my temperatures are correct (1-21) and i want to make sure my
q' is correct. Thank you
rectangular channels are machined. The blade, which has a thermal conductivity of k= 100 W/m-K, is 6mm thick, and each channel has a 2mm x 6mm rectangular cross section, with a 4-mm spacing between adjoining channels. Combustion gases Tooho Air channel Tojshi 2 mm 6 mm 6 mm 4...